Standard fog lights (PTF) on the Lada are only available in the “Lux” trim levels. If you are the owner of a car with a simpler configuration (“Norma” or “Standard”), then you can install PTF on a sedan, station wagon, hatchback or liftback yourself according to the simplest and most universal scheme..
Preparatory stage (selection of PTF for Lada Granta)
The range of PTFs is not large; it is represented by several domestically produced models. Some owners claim that PTFs from Opel and Ford are compatible, but the information has not been verified.
| Name / manufacturer / article | Price, rub.) |
| LADA Granta (VAZ 2190) / Kalina 2 / LADA Largus OSRAM Kit 21900-3743010 | from 2800 |
| Kit 21900-3743011 | —/— |
| —/— 2190-3743011 | —/— |
| —/— 2190-3743010 | —/— |
| PTF wiring kit for LADA Granta (2190 2874498) | from 600 |
| PTF "LUCH" set 1118-3743010/11 | from 1800 |
| PTF glass (02B08507) Granta / Kalina 2 / Largus, Datsun | from 750 |
| AUTOMOTIVE LIGHTING / BOSCH (982469641) | from 2000 |
*prices are as of September 22, 2018.
Procedure for self-installation of fog lights on a Lada Granta liftback
We place the car on a flat platform with access around the perimeter.
- We dismantle the front bumper along with the radiator grille.
- Using a milling cutter, we cut holes in the openings for the PTF.
- We install the fog lights and secure them to the fasteners.
- We connect the blocks with wires.
- Reinstall the bumper. We check the functionality of the system.
Installation
Required
:
- buy PTF (articles: 21900-3743011-00 and 21900-3743010-00), for example here. For Lada Granta FL, PTF catalog number: 261500097R.
- PTF activation button (article 759.3710-07.01A or 995.3710-07.06).
Where can I buy?
This and other accessories are presented at the lowest prices in our online store (PTF Grants, PTF Kalina, PTF Priora).
To install the PTF in the bumper, it must be removed. Then cut holes of the required diameter. Sand the sawn edges with sandpaper. And secure it to the fog lights in the bumper using screws. There shouldn't be any difficulties at this stage.
The whole process is also shown in the video:
Step-by-step process for preparing and installing fog lights
In the auto store we purchase: PTF, corrugation (at least 3.0 m), adapters - adapters for PTF with standard wiring.
- To remove the front bumper, unscrew three self-tapping screws on each side, four plastic clips, three “10” bolts in the lower perimeter;
- We remove the structure along with the radiator grille;
It is important to know!!! In the Norma and Standard models, there is no hole for adjusting the fog lights. The owners independently cut out a diameter of “8”. In the Liftback body modification, the opening is factory-made.
- We cut out the opening for the fog lights along the contour, it is factory-made;
- To make it smooth, treat the surface with a household hairdryer;
- We fix the headlights on three standard mounts;
- We connect adapters to each of the lamps, since the standard block with wires is short, its length is not enough;
- We put on the front bumper, screw it in with bolts and plastic clips.
conclusions
As you can see for yourself, in order to carry out a competent and correct installation of the PTF on the Grant frets, great skills and knowledge are not required. You just need to strictly follow our instructions and maintain skill and patience.
The last step will be to adjust the PTF so that driving the car is safe not only for you, but also for all other drivers traveling in the opposite direction.
In the standard configuration Norma, Standard, Lux, Liftback, fog lights (hereinafter referred to as PTF) are not installed in the front bumper. Instead of accessories, plastic plugs are built in. Let's look at how to install fog lights on a Granta liftback step by step below.
Wiring diagram for fog lights Lada Granta liftback
Engine compartment
- We lay an additional wire from the right PTF headlight to the left one. We solder it and bring it into the engine compartment to connect to the relay.
- We fix the mass to the body at the place where the bumper is attached, maybe under the license plate, in the center.
- Do not forget to lay all electrical wiring in a corrugated material made of fireproof material.
Interior of the Lada Granta liftback car
- We lay the corrugated hose through the hole in the hydraulic corrector seal.
- The connection is best made at the ignition switch. That is, when turned off, the headlights will go out automatically.
- Open the glove box lid, press the side stops, and remove the lid.
- We stretch our hand into the cavity and carefully squeeze out the block of two buttons for controlling the heated glass and PTF.
- We power the minus from the heater button. Plus we won’t take it, since they will be activated at the same time.
- We connect the positive cable and install the unit again.
- We connect to the positive from the ignition switch unit (blue wire), it is located under the steering wheel.
- Finally, we power the relay - regulator: ground - wire from the button - end to the PTF - plus to the ignition.
In each specific configuration, the color scheme of the wire may differ. Read the diagram in the instruction manual for details. Classic colors: red, yellow, blue, brown. If you do not want to supply power through the ignition switch, the connection diagram is simplified with one less procedure.
How to install fog lights on a Grant?
The Lada Granta comes from the factory in three trim levels: “Lux”, “Norma”, “Standard”. In this case, only the first of them receives fog lights. The second and third places for installing “foglights” have a corresponding button on the panel, but there are no headlights themselves. Connecting PTFs can be entrusted to service station specialists, but installing them yourself using a ready-made scheme is both cheaper and more pleasant.
Rules for installing foglights on Lada
Properly installed PTFs help the driver control the car in difficult road conditions. Traffic rules strictly regulate the height of headlights, their color, as well as the position of light spots on the road.
Where can I install PTF
In the design of the modern Granta, the installation locations are precisely worked out: under the license plate, on the sides. Some bumpers even have recesses there . In any case, for proper installation, the front bumper of the car will have to be removed.
But before that, you should go shopping and find the necessary parts. Today's market offers both bumpers with recesses and bumpers with headlights already installed. The choice, as always, remains with the owner.
Most Lada Granta cars do not have fog lights, but there are recesses in the bumper for do-it-yourself installation
Instructions for installing headlights for dummies
The entire process of equipping a car with foglights can be divided into several stages:
- Removing the bumper.
- Installation of headlights.
- Wiring.
- Connecting headlights.
- Reassemble the parts in reverse order.
Removing the front bumper
The Granta's bumper is integral with the radiator grille, so in order not to distort the latches under the wings, it is advisable to remove it together with a partner.
Photo gallery: necessary tools
Universal Phillips screwdriver with replaceable blade 10 mm combination wrench 8 mm combination wrench Universal torx t20 wrench
- crosshead screwdriver;
- 10 mm wrench, 10 mm socket;
- 8 mm wrench;
- TORX T-20 wrench.
Bumper removal algorithm
- Unscrew the front license plate.
To access the mounting bolts, remove the front license plate - There are two mounting bolts under the bumper. Unscrew them with a 10 mm head.
- After opening the hood, remove the six bolts securing the radiator grille.
With the hood open, find and unscrew the bolts securing the radiator grille - Unscrew the 3 bolts that secure the bumper from below.
The next step is to unscrew one of the bolts and a pair of screws securing the bumper, - Unscrew a pair of screws on each side connecting the fender liners to the bumper.
Unscrew a pair of screws on one and the other side of the bumper - After this, remove a pair of screws from the side of the wheel arches.
Unscrew four screws in the wheel arches - a pair on each side - Pull the corners of the bumper forward in the direction of travel and remove it.
DIY headlight installation
For the Lada Granta, two types of headlights are offered today:
- Bosch - with flat glass;
- Kirzhach is convex glass.
Both headlights are standard, so their choice is up to the consumer.
What tool do you need?
In addition to headlights, to equip a car with PTF you must have:
- self-tapping screws (6 pieces for attaching headlights);
- drill;
- set of drills;
- countersink or sandpaper;
- stationery knife;
- sealant.
Experts recommend installing headlights in accordance with the following plan:
- A hole with a diameter of up to 10 mm is drilled in the center of the oval for the headlight.
Make a 10mm hole in the center of the notch to start cutting - Starting from this hole, cut a circle along the inner diameter with a stationery knife.
Starting from the center of the hole, carefully cut out a circle of the required size.It is better to cut the hole in several steps so that your hand does not slip and damage the bumper.
- Use sandpaper or a countersink to process the hole, the contour of which should be equal to the outer diameter of the headlight.
After cutting the hole for the headlight, sand it down so that it does not extend beyond the outer diameter - Using self-tapping screws, install the headlight in the bumper.
Secure the headlight using self-tapping screws - The cracks remaining after work are filled with sealant.
After installing the headlight, coat all joints with sealant.
The last paragraph of the instructions is optional. However, experts recommend not to neglect it, otherwise dirt, snow or water may get into the cracks.
The steps described above are repeated in the same sequence to install the second headlight.
How to wire and connect a headlight
To connect the PTF you will need various tools:
- installation kit for connecting fog lights on Grant. It includes a button, a relay, wiring in the cabin, wiring under the hood;
- corrugation (for example, 9 mm for the interior and 16 mm for the hood);
- insulating tape;
- drill;
- set of drills;
- 10 mm head;
- 13 mm wrench.
An installation kit for connecting fog lights on a Grant will make the car owner’s work much easier
Step-by-step instructions for installing a rear fog light
Many Lada Granta Liftback car owners are surprised to hear about this, but it is a fact. Of course, we are not talking about PTF in its classic form, but about a laser brake light. It is installed in the rear of the car and informs the driver behind about the vehicle. Since there is no strictly defined installation location, it is customary to fix it in the area of the license plate, under the lower contour of the bumper, in the spoiler. There are known cases of embedding an accessory inside.
A bright red light beam informs drivers behind, preventing accidents. The brake light is also used when it is necessary to notify the driver of the need to switch the high beam headlights. An alternative way to use lighting when backing up or parking in conditions of limited visibility. The maximum effective beam length is 25.0 meters. Exceeding the length does not guarantee the quality of lighting.
The voltage is supplied from the left/right brake light. Activation is possible either by pressing the brake pedal or by a separate button. The owner makes the decision based on personal beliefs. In practice, activation occurs with an autonomous button, since when driving backwards it is not always advisable to use the standard brake pedal. It is strictly forbidden to point the laser beam at the windshield area behind the driving driver.
Connection
Below is a universal diagram for connecting a PTF using an additional button. The PTF kit contains everything necessary for installation and connection. In some cases, it may be necessary to lengthen the wires (cross-section of at least 0.75 sq. mm), be prepared for this.
It is recommended to hide the wiring under the hood in corrugation (cambric). We route the wires from the engine compartment to the passenger compartment through standard holes in the engine panel (the hole above the pedals). It is most convenient to place the relay inside the panel, behind the light control module (LCM). Plus, for switching the PTF, we take it from the battery or in the mounting block (most often this is a thick pink wire). Other useful contacts can be found in the table from the article on installing an alarm system. We install the button in any place convenient for you.
Reviews
| № | Positive |
| 1. | Kirill , 36 years old: after purchasing a Lada Grant from the showroom, I immediately purchased a PTF from OSRAM 21900-3743010. I didn’t install it at the service station because I can do it myself. In general, I am satisfied with the quality of lighting, no complaints. |
| 2. | Vitaly , 29 years old: it is obvious that there are not enough foglights out of the box. I often drive at night and need a good view of the road. Since I don’t understand manufacturers, I entrusted it to a specialist at a service station. PTF Lada Granta liftback - my advice. |
| 3. | Georgiy , 37 years old: I’ve been working as a taxi driver for the second year, my shift often ends after one in the morning. The disadvantage of the standard lighting system is obvious. I bought a “LUCH” set 1118-3743010/11 at the market. The cost is 1850 rubles, the quality is good, installation couldn’t be simpler. |
| 4. | Victor , 25 years old: I work as an entrepreneur, purchasing goods from hundreds of kilometers away. By morning the products should be on the counter. To help the standard headlights, I installed PTF. Second week, no complaints. |
| 5. | Maxim , 28 years old: I leave my positive review of BOSCH fog lights (982469641). Special thanks to the store manager for his practical advice. |
| 6. | Konstantin , 37 years old: during scheduled maintenance, he ordered the service of installing a PTF from a technician. I chose OSRAM 21900-3743010 because the price and quality are at a decent level. Numerous positive reviews. |
| 7. | Vladimir , 48 years old: I was a little upset by the lack of fog lights from the box on the Lada Granta liftback. I had to install it myself last weekend. The lighting is good, no complaints. |
| Negative | |
| 1. | Alexander , 36 years old: not only are fog lights not included in the kit, but they also provide poor lighting. We are talking about a domestic manufacturer. Installed by BOSCH (982469641). I use it myself and recommend it to others. |
| 2. | Vitaly , 39 years old: installed domestic PTF OSRAM 21900-3743010. I regretted buying it, wasted money. The quality is below average, the angle of inclination is several degrees. I don't recommend it. |
| 3. | Vyacheslav , 37 years old: not happy with the installed fog lights, they don’t cover the side of the road, visibility is mediocre, the light is dim. |
Conclusion Every product has its own buyer. If you don’t find fault with a budget car, which is the Lada Granta Liftback, the quality of PTF lighting is good, it is enough for visibility. Of course, when compared with headlights from foreign brands in the premium segment, the advantage of the latter is obvious. In order to increase the service life of accessories, purchase products exclusively from certified points of sale. Require the provision of documents, check the functionality on site.
Connection methods
Installation of the PTF switch off button
So, if the installation of fog lights is carried out at home, then in order to do everything correctly, put the kit in the bumper instead of plugs and connect it to the wiring, you can use one of two connection options. As we remember, PTFs are not turned on by side lights in any case; this must be remembered before installing the kit in the bumper and connecting all connectors. There may be several options for installing devices. One of the easiest in terms of installation and reliability is to connect to vehicle wires that are already wired and designed for fog lights.
In this case, everything can be made simpler. The factory wiring is already equipped with all the necessary components, in particular, the wires and connectors that are needed for connection. The wiring contains all the relays and fuses, as well as a switch that can be used to control the devices. In fact, all you have to do is remove the plugs from the bumper and install the PTF kit, connecting it to all connectors. This option is not relevant for all vehicles, but only for cars equipped with plugs or cars where it is necessary to change faulty fog lights (the author of the video is Andrey Kuvshinov).
When purchasing a PTF kit, you need to make sure that this model can be installed on your car. Not only the connectors must match, but also the installation parameters. If the vehicle is not equipped with wiring for installing fog lights, you will need to do it yourself. In order for the fog lamp connection diagram to be correct, additional wires should be purchased along with the kit; they must be copper and insulated. In addition, you also need to purchase a fog light switch, a fuse and a relay; sometimes these components are included with the PTF.
Remember that under no circumstances should fog lights be turned on along with the dimensions. Standard wiring and switch are not designed for the level of current these optics draw.
It should be noted that the electrical circuit must in any case be equipped with a fuse, this is very important. Only a fuse will save your vehicle from fire if a short circuit accidentally occurs in the circuit
The fuse itself must be powerful enough - the power level is calculated in accordance with the power of the optics itself.
For example, if the optics are designed for 60 watts, then when purchasing a fuse, you must calculate its power in advance in accordance with the formula:
60 W * 2 / 12 V = 10 A
That is, the device itself must be selected taking into account a small margin. The best option would be to purchase a 15 amp fuse.
