Design features, troubleshooting and replacement of the VAZ 2107 camshaft

Camshaft VAZ 2107

The camshaft is the main element of the gas distribution mechanism of a car engine. This is an all-metal part, made in the form of a cylinder with support journals and cams placed on it.

The camshaft contains cams and journals

Purpose

The timing shaft is used to control the processes of opening and closing valves in the combustion chambers of the engine. In other words, it synchronizes the operating strokes of the power unit, promptly admitting the fuel-air mixture into the combustion chambers and releasing exhaust gases from them. The camshaft of the “seven” is driven by the rotation of its star (gear), connected through a chain to the crankshaft gear.

Where is it located?

Depending on the design of the engine, the timing shaft may have a different location: upper and lower. With its lower location, it is installed directly in the cylinder block, and with its upper location, it is installed in the cylinder head. For "sevens" the camshaft is located in the upper part of the cylinder head. This arrangement, first of all, makes it easily accessible for repair or replacement, as well as for adjusting valve clearances. In order to get to the timing shaft, just remove the valve cover.

Operating principle

As mentioned, the camshaft is driven by the crankshaft gear. At the same time, its rotation speed, due to the different sizes of the drive gears, is reduced exactly by half. The full operating cycle of the engine occurs in two revolutions of the crankshaft, but the timing shaft makes only one revolution, during which it manages to let the fuel-air mixture into the cylinders one by one and release the exhaust gases.

The opening (closing) of the corresponding valves is ensured by the action of the cams on the valve tappets. It looks something like this. When the shaft rotates, the cam with its protruding side presses the pusher, which transmits force to the spring-loaded valve. The latter opens a window for the intake of the combustible mixture (exhaust of gases). As the cam rotates further, the valve closes under the action of a spring.

The valves open when the protruding parts of the cams press on them

Characteristics of the VAZ 2107 camshaft

The operation of the VAZ 2107 timing shaft is determined by three main parameters:

• phase width - 232o;
• intake valve lag - 40°;
• exhaust valve advance - 42o.

The number of cams on the camshaft corresponds to the number of intake and exhaust valves. The "seven" has eight of them - two for each of the four cylinders.

Find out more about the operation of the timing belt: https://bumper.guru/klassicheskie-modeli-vaz/grm/grm-2107/metki-grm-vaz-2107-inzhektor.html

Preparatory stage

To set the ignition on a VAZ 2107 , no special conditions are required; the operation can be done both in the garage and on the street, including in winter. For work, prepare the following set of tools:

• flat screwdriver;
• metal probe 0.35 mm thick;
• open-end wrench size 13 mm;
• a car light bulb designed for a voltage of 12 V with wires soldered to it;
• a wrench with a long handle designed to turn the crankshaft;
• key for unscrewing spark plugs.

Note. Instead of a special key to rotate the crankshaft, you can use a regular open-end wrench measuring 36 mm. If you don’t have such a key, then you will have to set the marks in the old proven way: by engaging 4th gear and raising the rear wheel, turn it manually, thereby turning the crankshaft.

Ideally, it is better to have in your arsenal a device for setting the ignition on a running engine - a strobe light. It is equipped with a lamp that flashes simultaneously with the moment of spark formation in the cylinder, which allows you to see the position of the notch on the crankshaft pulley at idle speed and clearly adjust the advance angle.

Important point. The ignition is set in order to ensure that the spark appears in a timely manner and the engine starts, after which additional adjustments will be required. But the latter will not bring you the desired result when there is no compression in the cylinders or problems with the carburetor make themselves felt. If these faults are not eliminated, the engine operation will remain unstable, no matter how you configure the spark generation system.

Hence the conclusion: you can set the ignition correctly at any time, but to set it well - only on a working engine and carburetor.

ICE theory: Motor 2103 with head 21214 with reg. star (modern)

2:17 — How to measure compression 9:55 — How to install an adjustable sprocket 10:00 — How to set up a split gear.

VAZ 2107 injector - treatment of tripping and misfires

Diagnostics revealed that the fourth gasoline injector was clogged, tripping and multiple misfires in all.

Is it possible to increase the power of a VAZ 2107 engine by installing a different camshaft?

Probably, every owner of the “Seven” wants the engine of his car to work not only without interruptions, but also with maximum efficiency. Therefore, some craftsmen are trying to tune power units using various methods. One of these methods is to install a different, more “advanced” camshaft.

The essence of tuning

Theoretically, it is possible to increase the power performance of a power unit by increasing the phase width and lift height of the intake valve. The first indicator determines the period of time during which the intake valve will be open, and is expressed in the angle of rotation of the timing shaft. For the “seven” it is 232o. The lift height of the intake valve determines the area of ​​the hole through which the fuel-air mixture will be supplied to the combustion chamber. For VAZ 2107 it is 9.5 mm. Thus, again, in theory, as these indicators increase, we get a larger volume of combustible mixture in the cylinders, which can really have a positive effect on the power of the power unit.

The phase width and lift height of the intake valve can be increased by changing the configuration of the corresponding cams of the gas distribution shaft. Since such work cannot be done in a garage, for such tuning it is better to use a finished part from another car.

Camshaft from Niva

There is only one car whose camshaft is suitable for the “seven”. This is a VAZ 21213 Niva. Its timing shaft has a phase width of 283°, and the intake valve lift is 10.7 mm. Will installing such a part on a VAZ 2107 engine give anything in reality? Practice shows that yes, there is a slight improvement in the operation of the power unit. The power increase is approximately 2 liters. s., but only at low revs. Yes, the “seven” responds a little sharper to pressing the accelerator pedal at the start, but once it gains speed, its power becomes the same.

Sports camshafts

In addition to the timing shaft from Niva, the VAZ 2107 can also be equipped with one of the shafts made specifically for “sports” tuning of power units. Such parts are produced by a number of domestic enterprises. Their cost ranges from 4,000–10,000 rubles. Let's look at the characteristics of such camshafts.

Table: main characteristics of “sports” timing shafts for VAZ 2101–2107

Why install a different camshaft?

The main reason for installing a new part is to replace it in case of failure. But sometimes such a decision is made for other reasons. For example, a car owner dreams of improving engine performance. And for this he begins to tune the engine. It is believed that a more advanced camshaft can help improve engine performance.

How is this achieved? Another device may make it possible to increase the valve lift and the width of the engine's operating phase. In theory, this should help produce more mixture, which will improve performance.

And there are so many things that numerous “amateurs” are trying to cram into the cylinder head. But there is only one car that can become a “donor” for installing a new device. And this is everyone’s favorite Niva (VAZ 21213). The Niva camshaft is an ideal solution for tuning the 7 engine!

The phase width of this part, as well as its intake valve lift, are relatively suitable for the operation of the Seven engine. And the engine receives an increase in power of about 2 horsepower. Of course, this is not such a big deal. But at the start the car responds a little better.

If a car enthusiast is willing to pay money for a special “sports” shaft, then he may well buy one that is manufactured in domestic factories for this purpose. Today you can find a worthy “comrade” within 10 thousand rubles.

Malfunctions of the VAZ 2107 camshaft, their symptoms and causes

Considering that the timing shaft is subject to constant dynamic and temperature loads, it cannot last forever. It is difficult even for a specialist to determine that this particular unit has failed without detailed diagnostics and troubleshooting. There may be only two signs of its malfunction: a decrease in power and a quiet knocking sound, which manifests itself mainly under load.

The main camshaft faults include:

• wear of the working bodies of the cams;
• wear of the surfaces of the bearing journals;
• deformation of the entire part;
• shaft fracture.

More about timing chain repair: https://bumper.guru/klassicheskie-modeli-vaz/grm/grm-2107/kak-natyanut-tsep-na-vaz-2107.html

Wear of cams and journals

Wear is a natural occurrence for a constantly rotating part, but in some cases it can be excessive and premature. This leads to:

• insufficient oil pressure in the system, as a result of which lubricant does not flow to loaded areas or is supplied in smaller quantities;
• low-quality motor oil or one that does not meet established requirements;
• defect in the production of the shaft or its “bed”.

If the cams wear out, the engine power is noticeably reduced, since they, being worn out, cannot provide either the appropriate phase width or the required lift of the intake valve.

When the cams wear out, engine power drops

Deformation

Camshaft deformation occurs as a result of severe overheating caused by malfunctions of the lubrication or cooling systems. At the initial stage, this malfunction may manifest itself in the form of a characteristic knocking sound. If you suspect such a breakdown, further operation of the car is not recommended, as it can damage the entire gas distribution mechanism of the engine.

Deformation occurs due to malfunctions in the lubrication and cooling systems

Fracture

A camshaft fracture may be a consequence of its deformation, as well as poor timing. In the event of this malfunction, engine operation stops. In parallel with this problem, others arise: destruction of the shaft “bed”, bending of valves, guides, damage to parts of the piston group.

A shaft fracture may be a consequence of deformation

How to understand that the camshaft needs to be changed?

You can determine a camshaft malfunction without opening the hood by two signs:

The main reason for malfunctions in the camshaft is the appearance of gaps. They appear between the shaft bearing journals and the bed bearings on which the camshaft rests. The cracks are formed due to the fact that parts of the camshaft are worn away. Gaps cause the shaft to move in the vertical or horizontal axis. If the shaft play is 1 mm, then this affects the operation of the engine. Reasons for gaps:

The camshaft also needs to be changed if the oil channels in it are clogged. Before changing the part, look for any play, fracture, deformation or scuffing of the shaft.

Troubleshooting the VAZ 2107 timing shaft

When the camshaft is removed from the “bed”, it is necessary to assess its condition. First this is done visually. The camshaft must be replaced if its working surfaces (cams and bearing journals) have:

• scratches;
• bullies;
• cut wear (for cams);
• enveloping a layer of aluminum from the “bed” (for support necks).

In addition, the camshaft must be replaced if even the slightest traces of deformation are found.

The degree of wear of the support journals and the supports themselves is determined using a micrometer and caliper. The table below shows the permissible diameters of the journals and working surfaces of the supports.

Defect detection is carried out using a micrometer and calipers

Table: permissible diameters of the camshaft journals and its “bed” supports for VZ 2107

If during the inspection it is determined that the dimensions of the working surfaces of the parts do not correspond to those given, the camshaft or “bed” must be replaced.

Installing a new camshaft

In order to install a new timing shaft, you will need the same tools as to dismantle it. The installation procedure is as follows:

1. Be sure to lubricate the surfaces of the cams, bearing journals and bearings with engine oil.
2. We install the camshaft in the “bed”.
3. Using a 10 mm wrench, tighten the bolts of the thrust flange.
4. We check how the shaft rotates. It should turn easily around its axis.
5. We set the shaft to such a position that its pin would coincide with the hole on the fixing flange.
6. We install the bed on the studs, screw on the nuts, and tighten them. It is important to follow the established procedure. The tightening torque is in the range of 18.3–22.6 Nm.

   
   The nuts are tightened using a torque wrench with a torque of 18.3–22.6 Nm

7. We do not install the valve cover and camshaft sprocket in place, since it will still be necessary to set the valve timing.

Setting ignition timing (valve timing) by marks

After the repair work has been carried out, it is necessary to set the correct ignition timing. To do this you need to do the following:

1. Install the camshaft sprocket with the chain, secure it with a bolt without tightening it.
2. Install the chain tensioner.
3. Place the chain over the crankshaft, accessory shaft and camshaft gears.
4. Using a 36mm wrench placed on the crankshaft pulley nut, rotate the crankshaft until the mark on the pulley aligns with the mark on the engine cover.

   
   Labels must match

5. Determine the position of the camshaft sprocket in relation to the “bed”. The mark on the star should also line up with the protrusion.

   
   If the marks do not match, you need to shift the sprocket relative to the chain

6. If the marks do not match, unscrew the camshaft sprocket bolt and remove it together with the chain.
7. Remove the chain and turn the sprocket to the left or right (depending on where the mark is shifted) by one tooth. Place the chain on the sprocket and install it on the camshaft, securing it with a bolt.
8. Check the position of the marks.
9. If necessary, repeat shifting the star by one tooth until the marks coincide.
10. Upon completion of work, secure the star with a bolt and the bolt with a washer.
11. Install the valve cover.
    Secure it with nuts. Tighten the nuts in the order shown in the photo. Tightening torque: 5.1–8.2 Nm. The nuts must be tightened with a torque wrench to a torque of 5.1–8.2 Nm
12. Carry out further engine assembly.

How to choose quality parts

Buy a camshaft from a reliable and time-tested company, for example, PJSC Avtovaz. The packaging has a seal with a hologram. It shimmers in the light and features the company's logo. There is also a sticker with a barcode on the box. The item is packaged in blue translucent film. There is a stamp from the Quality Control department inside the package. Buy rockers together with adjusting bolts. There are new and old style levers. The holes in them differ in diameter and number of cuts. If you buy rockers and bolts separately, chances are they won't fit together.