Ball joints for Lada Granta which are better

If you experience knocking noises from the front suspension, especially when driving on an uneven road with small holes or potholes, you should pay attention to the condition of the ball joints. On a Grant, factory ball joints can easily travel more than 100,000 km during normal operation, but there are also cases when this has to be done much more often. It is for such cases that this article will be written.

In order to replace the ball joints on the Grant, we will need the following tool:

1. Hammer
2. Mount
3. Puller
4. Key for 17 and 19
5. Torx head e12
6. Ratchet or crank

Photo report on replacing ball joints on Lada Granta

The first thing you need to do is put the car on a lift or jack up the front of it. After this, remove the wheel to gain access to the front suspension elements.

Then unscrew the two bolts securing the support to the steering knuckle, as shown in the photo below:

Then, using a 19mm wrench, we tear off, but do not completely unscrew the lower nut attaching to the front suspension arm of the Grant:

And now you can use a special puller to press the ball joint pin out of the lever, or use a hammer and pry bar for this purpose.

After removing the finger, you can remove the support completely, move the lever to the side:

If it is not possible to move the lever to the side using a pry bar, then you can use a jack and a brick, as is clearly shown in the photo below.

We take a new ball, remove the boot and thoroughly push it inside with lubricant, such as Litol. After which you can install the new ball in its place. Of course, you will have to suffer quite a bit until the support gets into place, but if you have a jack and pry bars, everything can be done without any problems.

We tighten all the bolts and nuts to the required torque and put all the other parts in their places. With this, we can consider this repair of the Lada Granta complete. The price of a new ball joint is no more than 400 rubles for the original product from AvtoVAZ. There are cheaper options, but in this case you can save on both price and quality!

How to check the condition of the front suspension of Lada Granta, Kalina and Priora

15 March 2021 LadaOnline 6 807

According to the maintenance regulations for Lada Granta, Lada Kalina and Lada Priora cars, the technical condition of the front suspension parts must be checked every 15,000 km. mileage You can determine the causes of knocks and squeaks in the suspension using self-diagnosis.

Layout of front suspension parts

1 — anti-roll bar; 2 — rubber-metal joint of the transverse arm; 3 — shock absorber strut; 4 - stretching; 5 — extension bracket; 6 — nut for fastening the extension to the bracket; 7 — ball support of the shock absorber strut; 8 — joint of the anti-roll bar; 9 — wishbone; 10 — bracket for securing the stabilizer bar.

How to check the front suspension

• Checking the front suspension should be carried out in the engine compartment and from below the car, mounted on an inspection ditch or supports (with the front wheels hanging out).
• The condition of the protective covers of the suspension ball joints (they should not be mechanically damaged) should be checked during each maintenance and repair of the vehicle.
• Check the condition of the rubber-to-metal joints, rubber cushions, suspension ball joints and the condition of the upper suspension strut mounts.
• Rubber-metal hinges and rubber cushions must be replaced in case of ruptures and one-sided bulging of rubber, as well as when their end surfaces are trimmed.
• Suspensions on rubber parts are not allowed:

• signs of rubber aging;
• mechanical damage.

Pay special attention to mechanical damage (deformations, cracks, traces of contact with road obstacles, etc.) of suspension elements, especially levers.

Procedure

:

1. Check the tightness of the shock absorber rod mounting nut.

2. Check the tightness of the nuts securing the upper strut support to the body. Similarly, check the fastenings of the rod and the upper support of the second rack.

3. Check the condition of the protective covers of the ball joints. If the boots are damaged, replace the ball joints.

4. Check the ball joints for play. To do this, measure the distance H (see Fig. 7.1) between the transverse arm 17 and the brake disc 21. Insert the mounting blade A (see photo) between the steering knuckle and the suspension arm and, leaning on the lever, try to swing the steering knuckle. If this distance changes by more than 0.8 mm when the suspension is rocked, replace the ball joint.

5. If the ball joints are in good condition, rock the wheels in a vertical plane and make sure there is no play in the hub bearings. The maximum permissible axial clearance is no more than 0.015 mm. If the gap is greater than the specified value, replace the bearings.

Advice

: When swinging the suspended front wheel, it is difficult to distinguish play in the hub bearings and ball joints. Ask an assistant to press the brake pedal: if you feel play in this case, then the ball joints are faulty.

6. Check the rubber-to-metal joints in the places where the transverse arm is attached to the body bracket for play.

7. To do this, insert a mounting spudger or a large screwdriver into the gap between the lever and the bracket and try to rock the lever. If there is significant play, it is recommended to replace the lever assembly with hinges.

8. Check the rubber-metal hinges for attaching the stabilizer struts for play. To do this, insert the mounting blade between the wishbone and the stabilizer bar and rock the bar. If necessary, replace the stabilizer links.

9. Check the tightness of the nuts securing the brace to the lever...

10. ...and to the extension bracket.

11. Check the tightness of the nut securing the stabilizer link to the front suspension arm. Replace the racks whose hinges have noticeable play.

12. Check the condition of the rubber cushions where the stabilizer bar is attached to the body.

Causes of malfunctions in the front suspension

Cause of malfunction
Remedy

Noise (knocking) in the suspension when the car is moving Fluid leakage from the strut Frequent “breakdowns” of the suspension Insufficient resistance of the suspension strut during the recoil stroke Increased clearance in the ball joint The car pulls away from straight-line motion Increased wear on the tire tread Uneven wear on the tire tread

Video review on replacing ball joints on Grant

For those who are too lazy to understand photo reports, everything can be shown clearly and easily using the example of a video review, which was taken from open sources.

This concludes this repair report.

Lada Granta is one of the cheapest and most affordable cars on the Russian market. The vehicle is built on a common platform with Kalina and has similar technical characteristics. However, as for the suspension, the Lada Granta has been slightly modified. Read more in our article about how the chassis on the VAZ 2190 is designed and what its malfunctions are.

The best ball joints VAZ 2110-12

Ball joints are another important element of a car’s suspension whose condition needs to be monitored. A high-quality ball joint is a guarantee of confident movement. We choose high-quality ball joints for the VAZ 2110. What is a ball joint? This is a unit (catalog number 2110-2904192) that connects the hub on the steered wheel and the suspension arm. Its task is to ensure that the hub can be rotated with the initial position of the wheel horizontally during vertical movement. A breakdown of the ball joint of a VAZ 2110 (or other front-wheel drive car) is not as bad as on a classic, when the wheel moves to the side, but still this element of the suspension requires attention. Moreover, ball joints and silent blocks are the most vulnerable parts of a car’s chassis. The durability of ball joints is affected by the quality of the road surface (here everyone remembered Russian roads ), and a breakdown can occur when the car hits a bump or a hole. If you hear noises while driving extraneous noise in the wheel area, then one of the reasons may be worn ball joints. When replacing, you can also determine the condition of the ball joints; if the finger of the ball joint in the ball joint moves more than 0.7 mm due to hand effort, then the ball joint needs to be replaced. So, let’s vote and leave reviews about the ball joints of the VAZ 2110-12:

1. What ball joints did you buy?
2. What were the ball joints like before and how long did they take?
3. Impressions and comments on the operation of ball joints

ps all off-topic comments will be deleted.
xn--2111-43da1a8c.xn--p1ai

Front suspension "Lada Grants"

It has an independent suspension with wishbones and a stabilizer bar. Damping of vibrations is carried out by hydraulic shock absorbers. The main structural element is the stand. It includes a swivel bearing, shock absorber and spring. The latter uses coils of variable diameter. The spring itself is made of a metal rod with a circular cross-section. It can have variable and constant hardness.

The pillar support has also been improved. Suspension creaking on the Lada Granta appears much less frequently than on Kalinas and Priors. To reduce roll, the design includes a stabilizer bar. It is made of spring steel. The stabilizer is installed with its ends to the lower suspension arms. Its middle part is fixed to the body.

Rear suspension

Unlike the front, it has undergone virtually no changes. Here, just like on the first Soviet G8s, a semi-independent beam is used. It is attached to the body on hinges (fortunately, there are no “crabs” in the design). A helical spring with constant stiffness is used as an elastic element. To dampen vibrations and prevent swinging, two shock absorbers are used.

• High reliability. The design does not have additional levers, which, in addition, can bend when falling into a large hole.
• Energy intensity. The Lada Granta absorbs all bumps perfectly, especially if oil shock absorbers are installed at the rear.
• Cheap maintenance. Due to its simple design, this pendant can be rebuilt even with your own hands. And the cost of new rubber-metal elements is unlikely to empty the pockets of even the most stingy car owner.

The main difference between the “Grant” suspension is the wheel alignment angles.

Shock absorber

This element is a damping device. The shock absorber serves to reduce the range of vibrations of the car body. In other words, the element prevents spontaneous rocking. The work of the shock absorber is based on hydraulic resistance. Inside it there is a liquid of a certain viscosity. It moves through a special valve. Thus, the device absorbs sharp impacts while preserving vulnerable suspension parts. Therefore, the shock absorber is one of the most important components in the chassis. On our roads, this element lasts about 60-80 thousand kilometers. But this period may be shorter, even with careful driving. It is enough just to damage the protective boot, and all the dirt will accumulate in the rod seal.

Also note that the damping element changes in pairs. That is, in the event of a breakdown of the rear left shock absorber, the rear right shock absorber also changes. As for the front struts, they are more durable. Often they are replaced already assembled with a spring, since they fail no earlier than after 150-200 thousand kilometers.

Which racks to choose for the Lada Granta - install normal spare parts

Selecting quality parts for car maintenance and repair is an important task for every motorist. In order for the car restoration to be high-quality and durable, it is better to use the most interesting options for parts with a sufficiently high quality. It is worth remembering that the reliability of spare parts determines their service life, as well as the quality of operation. Unfortunately, the cost of parts also greatly depends on this factor. Today we will talk about the racks that are best used on the Lada Grant. Considering the fact that factory suspension elements fail after a maximum of 50,000 kilometers, you have to look for something more interesting and non-standard. You can buy factory solutions again only under warranty, when you will receive a free replacement and will not charge money directly for the racks.

Today you can buy a shock absorber liner from any manufacturer, including some of the most amazing brands from around the world. In this case, it is not necessary to change the rack assembly; you can make a constructor by installing an insert of a specific selected type. This will completely change the behavior of the car. The stock shock absorbers on the Grant are simply amazing - they behave exactly as the Lada 2110 did back in 1998. There have been no significant changes in the suspension. At least regarding the struts and operating comfort of the car. There are different brands and specific recommendations for the types of racks. Let's take a closer look at each aspect of purchasing new suspension parts. This will help you better service your car and obtain the necessary features for operating a vehicle.

Oil or gas-oil - the first question that needs to be resolved

If you take inexpensive racks that are made in Russia or China, then there are virtually no differences between oil and gas-oil. But when you buy products from a great brand, you can notice a very noticeable difference. In particular, gas-oil will be a very tough sports solution. Oil shock absorbers offer customers a number of specific advantages that will be important in the operation of vehicles:

• quite high ride comfort, which can be called significant progress for the Lada Granta, overcoming most potholes without noticeable effects in the car interior;
• low level of penetration, that is, you will not catch unpleasant sounds when the rack shows its long free stroke, there is no risk of breakage;
• the rod stroke is quite long, it is possible to hang the wheels almost like an SUV, this helps on large bumps and dirt roads;
• your Lada Granta will not only become softer, but will also be able to transmit information about the road more energy-intensively, there is no intrusive data, only the necessary details;
• The cost of oil shock absorbers is often slightly lower than gas-oil shock absorbers, which is why the vast majority of domestic car owners buy them.

Of course, it all depends on the brand. You can buy an excellent Japanese version of the insert and get simply wonderful operating possibilities. There is the option of purchasing a cheap Chinese rack and being completely disappointed in its use. But for now, let's limit ourselves to making a decision on the type of shock absorber. It can be a soft oil or a sports gas-oil type.

Manufacturer is one of the most difficult questions for the buyer

Buying unusual, expensive shock absorbers is becoming a necessity today. In conditions of very tough competition and the global crisis in the automotive market, cheap companies are starting to produce worse and worse spare parts. Therefore, the products of some corporations have long ceased to be reliable and of high quality. It is worth highlighting the following brands as an ideal solution for Lada Granta when purchasing racks:

• KYB - you can combine separate liners with a stock strut and you will get an almost full-fledged Kayaba, the shock absorbers are very durable and high quality;
• Acomi is a fairly affordable brand, but much better than Chinese solutions, a completely acceptable solution if you choose an expensive series like Comfort PRO;
• SS20 - the company makes special racks for the Granta, so they fit perfectly, quite adequate quality, but there are many fakes and a number of shortcomings in movement;
• Demfi - not so durable, but quite affordable racks, which are also ideal for the Lada Granta, quite high-quality performance, but you need a choice;
• Plaza is one of the cheapest options of more or less decent quality, but only some kits from the manufacturer are pleased with their reliability and durability.

So there are not many chances to choose from brands. Of course, you can try Monroe struts or buy some racing solutions from France and Germany. But this will be too expensive. The same as Kayaba, but this solution is classic, and is simply perfect for the Lada Granta. If you have enough money for a Japanese manufacturer, buy their offers for your car.

Springs and strut supports for Lada Granta - choose the best

It is better to install original springs. No manufacturer offers the same accuracy as VAZ in this case. There is only one reason for this - no one wants a manufacturer of springs specifically for Grants to do it efficiently and cheaply. Therefore, you have to give preference to stock solutions. As for the upper and ball joints of the Lada Granta struts, it is worth paying attention to the following features:

• the upper supports of the front struts are most often installed in Russian SS20, there are options for using more expensive solutions, but this purchase takes a long time;
• but the rear upper supports for shock absorbers are not easy to find, the Acomi company will help you here, but it is better to contact the officials and buy what was originally in your car;
• VAZ ball joints are no good and cost 20-30 thousand, so it’s better to buy Belmag or Forward, which are made in Russia and cost very affordable money;
• you can also choose German Kraft ball joints, but here you should beware of fakes, so always choose parts based on price and quality with a specialist;
• It is better to buy any small details such as fasteners, bolts, nuts and washers from the factory, as otherwise you may simply not reassemble the car properly after disassembly.

There is an opinion that factory spare parts are always better than analog ones. But in the case of the Lada Granta this is not at all the case. Sometimes you can find quite adequate spare parts that fit Granta from German and Japanese brands. And then you can buy really wonderful additions and parts that last for years. However, any part has its own service life, and this also needs to be remembered.

Replacing Lada Granta struts and supports - several important features

If the rear suspension is more or less clear, then the front suspension always hides more mysteries. It is the front struts and supports that most often fail. Unless you constantly pull a trailer or tow careless friends. The load on the front of the car is always increased, so you often have to work with the front suspension parts. Changing the front struts on a Grant is not so easy:

• first you need to completely remove the rack and disassemble the lower parts of the chassis for subsequent installation on a new mechanism for damping road irregularities;
• if the rack is installed as a new assembly, then there will be much fewer problems, you just need to install a new one in place of the old mechanism and reassemble it in the reverse order;
• if only the liner is changed, it is worth completely disassembling the strut, removing the spring and taking out the shock absorber, checking the degree of wear of all parts and the need to replace them;
• Next, you should replace the strut liner, carry out technical checks right at the assembly site and reassemble the shock absorber to its original position;
• Next will be the installation of the rack in place, assembly and rough diagnostics of all the components that you repaired, this will give complete confidence in the quality of the work.

You need to acquire tools such as a set of wrenches and sockets, a spring puller, a pry bar, pliers, screwdrivers and other available tools. Otherwise, you will not be able to completely disassemble the part and carry out its normal restoration. Of course, there are certain difficulties in carrying out this process, so it is better to take your Lada Granta for service and complete all the work in just over an hour. We invite you to watch the video of the process of replacing the strut on front-wheel drive VAZ vehicles:

Let's sum it up

There are a number of features of operating the Lada Granta on Russian roads. For some reason, a domestic car is not very suitable for our roads; it crashes and fails instantly. Sometimes you come across a well-built car that doesn’t show any character after 100,000 kilometers. But in most cases, the Garnet justifies the title of the cheapest car in the Lada line. And when it comes to racks, the manufacturer saves a lot on these elements. The installation of low-quality suspension elements leads to the fact that more and more people, after purchasing Grants, repair it under warranty.

However, sometimes it is better to cancel the warranty and install normal racks, supports and other parts. In this case, you will ensure the normal service of your car’s suspension and will be able to establish normal operation of each unit. This will take a certain budget, but can provide you with comfortable movement without any particular difficulties or problems. Of course, even the best quality rack will eventually fail. But it can travel far beyond 100 thousand kilometers. What brands of spare parts do you choose to repair the suspension of your Lada Granta?

avto-flot.ru

Cause of malfunction

The main cause of element malfunction is a violation of the boot seal. Once it starts to crack, dirt and dust will get inside. They act on the ball like an abrasive. As a result, play appears and the support begins to break on its own. Is it possible to repair it? The Lada Granta suspension is designed in such a way that the ball joints cannot be restored and must be replaced entirely with new ones.