Lada XRAY: “insurance” crash test. How much will it cost to repair a hatchback?

Lada Vesta passed our “insurance” crash test using the RCAR method with a bang. And what about its half-brother, the XRAY hatchback: how much will it cost to restore it after a frontal impact from a speed of 15 km/h?

The bumper holds tightly to the wings - and transfers part of the impact energy to them

After meeting the barrier, XRAY waved its brushes in surprise: as happened on potholes on a cobblestone road, the shock caused the steering column lever to jump. Damage? The bumper cover was cracked, the hood was dented, the headlight was askew—we've seen worse faces after such blows. But there are small dents on both front fenders: this was done by the lining, which grabbed them with a death grip. But what’s worse is that the left wing, which had moved back, blocked the driver’s door, and the hood, which rested against the same wing near the windshield pillar, prevented the wing from being loosened and moved slightly forward. So we had to evacuate the dummy through the passenger door, get behind the wheel in the same manner and go to our technical center - fortunately, nothing leaked or fell off under the hood of Ixray.

It was possible to open the hood only by moving it a centimeter in its attachment to the left hinge

It was possible to break the closed, or rather, blocked circle, only with difficulty reaching the fastening of the hood to the left hinge: first they broke it, and then, by slightly moving the wing, the door.

The left wing was also damaged at the point of attachment to the mudguard.

And having finally separated the bumper lining from the wings, Uncle Vanya already whistled: immediately behind the left edge of the fairly dented cross beam, the designers installed an electronic transmission control unit and an electric power steering pump along with a reservoir. It’s good that both units escaped with only bent mounting brackets. What if the blow was more serious?

The seemingly intact left headlight (first slide) has a fatally damaged housing. The right headlight was also damaged: the ears of its upper mounts were cracked (second slide)

The seemingly intact left headlight (first slide) has a fatally damaged housing. The right headlight was also damaged: the ears of its upper mounts were cracked (second slide)

0 / 0

After all, XRAY is not Vesta; it is made from a different, looser dough. After similar blows to the related Nissan Almera, Renault Sandero and Duster, we dubbed the design of the front of the B0 platform plasticine - and XRAY, alas, was no exception. True, the cross beam on the Lada, unlike its counterparts, is conditionally removable: it is attached to the ends of the side members with bolts instead of welding. Why conditional? Because for the sake of structural strength, the beam, in addition to the fasteners, is placed on such a generous layer of sealant that tearing it off is no easier than cutting it off.

The cross beam and the upper body shelf for the radiator mounting are severely deformed

Behind the bumper trim there is crumbled plastic

0 / 0

All machines of the B0 architecture are deprived of “accordions”, that is, zones of programmable deformation. And therefore the role of the crushed element had to be played by the front part of the prefabricated left spar, which opened like a rose: the channel parted with the amplifier. And in addition, the subframe mounting bracket welded to the spar was deformed - fortunately the subframe itself remained unharmed, and the wave of deformation did not sweep further and did not wash away the remaining normal alignment angles of the front wheels.

In addition to the top shelf, its mounting posts were also damaged.

The radiator of the cooling system has lost its attachment to the subframe, but has not lost its tightness

0 / 0

But the radiator of the engine cooling system took a hit: the beam located closely, bent, gave way to it so that, although it retained its tightness, it lost its lower attachment to the subframe. The upper body shelf had a hard time, and along with it, both (upper and lower) left pillars of its fastening rose up like a hump. The left mudguard of the engine compartment was dented, so much so that the wing attachment to it was also deformed. And the list of damage, alas, is crowned by not only the left headlight with a completely broken housing, but also the right one with broken mounting ears.

Immediately behind the left “tail” of the crossbar is the transmission ECU (shown by the arrow) and the power steering unit (in the foreground)

The most unpleasant consequence of the impact is the damaged end of the assembled left spar

0 / 0

The scope of work is clear. How much will the repair cost?

On the way from the test site, we stopped at the nearest dealer near Moscow - this is Yakhroma-Lada on Dmitrovskoe Highway. The craftsmen busily “stripped” the XRAY and soon delivered a verdict: the hood, bumper trim, crossbar, top shelf, cooling system radiator and left headlight went to the landfill. But the entire spar does not need to be changed - only the damaged front part.

The promise to return the slightly dented right fender, the left mudguard of the engine compartment and the radiator shelf mounting rack to its original form was not surprising. However, in addition, they promised us not only to straighten the much more damaged left wing, but also to solder the broken plastic fastenings of the right headlight for 2,550 rubles. Atypical for a dealer - and very nice for the budget. Because one Xray headlight costs almost twenty thousand! And the bumper lining is made of nothing other than especially valuable types of plastic: then why would it cost at least twice as much as a similar part of the same Vesta?

In the calculation, which was sent to us by e-mail after the promised couple of days, the long list of spare parts culminated in the amount of 107 thousand rubles - consider that the entire “dealer” repair of the Lada Vesta will cost the same! And the waiting time for parts, as in the case of Vesta, was not encouraging: three to four weeks. It’s good that they didn’t break the price for the work: 40 thousand rubles for a decent amount of work is very godly.

Spare parts for repairs from official dealers will cost twice as much as labor

Specialists from the Autogermes company, located on Moscow's Krasnaya Sosna Street, estimated their efforts at almost 60 thousand (a standard hour costs not 850 rubles, but a thousand) - although they did not undertake to repair either the left wing or the right headlight. In the calculation they indicated much less necessary consumables than colleagues from Yakhroma-Lada, but at first they completely forgot about the front panel - I had to prompt them. Otherwise, the course of treatment for our XRAY was prescribed a similar one, and if we had decided to repair XRAY here, we would have paid at least 175 thousand rubles.

At the Torgmash dealership, built in the north of the Moscow ring road, a whole council looked at our Lada in surprise: you, they say, are the first on Ixray. Apparently, due to an excess of feelings, they didn’t even notice the damaged radiator, and instead of slightly adjusting the power steering bracket, they offered to replace the entire serviceable unit for 22,675 rubles. A long dispute about which of the event participants should draw up a list of damages culminated in several hours of waiting for the car and the highest fee for troubleshooting - 3,700 rubles. And we only creakingly demanded the calculation itself after a lot of phone calls nine days later! Spare parts without notes like EGUR would have cost 114 thousand, but the work was estimated at almost 80 thousand rubles. After all, if colleagues from Yakhroma allow themselves ten standard minutes to remove a headlight, then in Torgmash they set aside as much as forty for this most complex operation. And it takes a whole working day to paint and replace the bumper trim.

No, we'd better hurry up. Maybe from unofficial people?

We visited several workshops and were convinced that we couldn’t do without replacing parts of the side member, hood, left headlight and crossbar. But the right headlight and radiator at the GSK body service on Korneychuk Street and the MBS technical center on Melnikov Street, we undertook to return it to its original form. For the services you would have to pay 45 thousand rubles, and the parts from the shortened list would cost 60 thousand - a total of 105 thousand. It’s still a bit expensive: a dealer repair of the Lada Vesta would cost only a little more.

Restoration in a universal workshop is one and a half times cheaper than a dealership

At the Whiteside service station on Yuzhnoportovaya Street and in an unnamed workshop near Varshavskoye Shosse, they promised us the biggest savings on spare parts - not only by soldering and puttying the bumper trim, but also by patching the top shelf along with its racks. However, isn’t this the case when the miser pays twice? Moreover, funds from insurers must cover both garage repairs and restoration at the dealer. Specialists from the federal expert company Delta, to whom we traditionally turned for an answer, counted 154,300 rubles in payments under Casco and as much as 168,800 under compulsory motor liability insurance—more than that.

Perhaps this is the best that XRAY can boast after the blow. Indeed, in our ranking of costs in terms of the cost of body repairs at dealers, it was ahead of both the Lada Vesta and the Lada Granta and only symbolically lagged behind the Renault Sandero - but it was also inferior to it in terms of restoration costs in universal workshops due to high costs for spare parts.

And this, by the way, is not the end of the Ixree epic. Remember the problems with the 1.8 engine? The story about them is yet to come.

Crash test Lada X-Ray

The new Russian car Lada X-Ray is produced by AvtoVAZ with the expectation of receiving high quality marks not only from Russian, but also from foreign experts. The domestic manufacturer has set itself the goal of making a reliable and safe crossover that will be able to protect the driver and passengers from injury if the car gets into a traffic accident or under other unfavorable circumstances. Lada Xray has received a number of effective security systems that will increase its chances of passing testing.

In order to gain authority and trust from foreign experts and car enthusiasts, the manufacturers of the Lada X-Ray plan to receive three stars based on crash test results in the prestigious Euro NCAP rating. This crash test is carried out by the best cars in the world, and a high score based on the result of passing it is a kind of sign of quality and safety, which will open the door for Lada Xray to enter the foreign market. The test will be carried out shortly.

Technical features

The test presented the Lada X-Ray Cross, which combines a power body from Sandero and a subframe of VAZ’s own design. Who didn’t know, but the domestic automaker, no matter how much they scold it, devotes a lot of effort to the passive safety of its cars. In particular: they carry out mathematical modeling of a crash test and a computer calculation of possible damage.

A special feature of this model is that it weighs 200 kilograms more than the Sandero and has larger diameter front wheels (17 inches). As you know, it is the large diameter of the wheels that can change the picture of body deformation during a frontal impact for the worse, using the example of the UAZ Patriot. Therefore, the engineers from Avto-VAZ, with their fingers crossed, were waiting for the results of the Lada X Ray Cross crash test - let's see what happened.

Testing "Lada X Ray"

One of the tasks that the Lada X Ray car was supposed to provide was guaranteed driver safety in any, even the most unfavorable situations. To achieve this, the car was equipped with effective security systems. AvtoVAZ believes that when passing the most prestigious crash test in the Euro NCAP rating, the Lada X Ray should receive three stars. A high score obtained as a result of passing this test opens the vehicle to the world market, as it is regarded by everyone as a kind of “Sign of Quality”.

The Lada X Ray is awaiting crash testing according to the RCAR and ARCAR methods.

Crash test criteria

When passing a crash test in the Euro NCAP rating, the car is subjected to tests, based on the results of which experts evaluate:

• child safety;
• driver protection;
• passenger safety;
• the danger a vehicle poses to pedestrians.

Design solutions ensuring the safety of the driver and passengers

The developers of the Lada X Ray car laid down a high level of safety at the design stage. In addition, the car has a reinforced body equipped with a number of structural elements that improve safety. These include:

• built-in roof reinforcements;
• safety bars in all doors;
• additional protective beams in bumpers;
• side body pillars.

During the development process, many parts were tested using a computer and only then embodied in metal.

Successful completion of a crash test is impossible without equipping the vehicle with passive safety systems. The use of the well-known VO platform as a layout diagram made it possible to equip the vehicle with a large number of such systems, including:

• effective system for securing child seats;
• three-point inertial seat belts for the driver and all passengers;
• belt tensioners;
• L-shaped headrests;
• automatic door unlocking upon impact;
• front and side airbags.

The car is also equipped with the most modern electronic safety systems, including ABS, EBD, BAS, ESP, TCS, etc.

Crash test methods

In world practice, the term “crash test” is used to refer to testing vehicles for safety. These tests simulate different types of road traffic accidents in order to find out what kind of damage those involved can suffer. In this case, instead of living people, special mannequins are used. There are a large number of different types of crash tests, but the most common are tests carried out using the following methods:

1. Euro NCAP methodology. The modern, most prestigious type of comprehensive testing, which includes:

• frontal collision at a speed of 64 km/h with a deformable barrier, with the impact occurring at 40% of the width of the front of the vehicle (driver's side);
• side collision at a speed of 55 km/h with a deformable barrier;
• head-on collision at a speed of 55 km/h with a rigid barrier.

Based on the results of three tests, the overall safety rating of the car is determined using points and a 5-point system.

results

Automatic activation of the Era-GLONASS system - we reject the emergency call. The first glance at the car after an impact makes experts wary - a small crease on the windshield pillar, for modern cars with strong bodies, this is not typical - a bad “bell”.

We look at the threshold on the driver's side - it has sagged a little, the driver's dummy is sitting low, its knees resting on the panel, the seat has sank down along with the floor. The door opened without the help of a special tool, but noticeably wedged in the opening. The passenger appears to be doing quite well based on a quick examination.

The front part of the car was crushed as much as possible in order to dissipate the force of the frontal impact and not transfer it to the power cell of the passenger compartment. The video shows how the spar has folded. But the deformation went further - the subframe folded, but not enough, and transferred the impact to the floor under the driver's seat, as evidenced by the folds in the bottom and the crease in the strength part of the frame. That's why the driver's seat sank.

Unlike the Lada Vesta Cross, which had tears in these places, the body of the X Ray remained intact. The video above clearly shows that the threshold of the car and its bottom were not torn apart after the crash test - there is a deflection, but the metal is intact. The engineers' fears about the enlarged front wheels, which could worsen the picture of body deformation in the driver's seat area, were not justified; everything is fine.

Rear air suspension Lada XRay (rear axle).

• Year of release: from 2021 to present
• For models: Lada Xray
• Installation axis: rear
• Drive: front
• Article: 01025

Suitable for VAZ-21129, HR16DE Lada XRay

Released - 2021, 2021,2018

Benefits of use:

• Improved handling and ride quality.
• Variable ground clearance 5-10 cm.
• Side roll compensation.
• Does not require modifications.
• 1 year warranty.

A set of roll-type air springs is designed for installation on the rear axle of the Lada X-Ray. Installation is carried out instead of rear springs in standard (factory) places. Installation will not require additional modifications to the spring support areas or changes to the factory design. The kit will allow you to change the rigidity of the rear axle, significantly improving the smoothness of the ride due to the high absorption of irregularities. It becomes possible to change the clearance in the range of 5 – 10 cm.

The kit is designed taking into account climatic operating conditions in Russia. Pneumatic cushions are resistant to low temperatures, abrasives and reagents. All products come with a 1 year manufacturer's warranty. The kit also includes certificates confirming the possibility of using these products in a vehicle structure.

The kit can be equipped with 1 or 2 nipples for adjacent or independent pumping. Additionally, you can install a supply and discharge system from the passenger compartment, as well as an air intake system for inflating wheels or a pneumatic signal.

The price for the rear air suspension of the Lada Xray is indicated for

• Roll air bags - 2 pcs.
• Fastenings (a complete set for the rear axle that does not require modifications)
• Highway - 7 meters
• Pumping nipple - 1 piece
• Fitting
• Certificate
• Instructions

Additionally, it is possible to install a monitoring and control system for the air suspension from the passenger compartment.

You can buy rear axle air springs for XRay (XRay) in any region of Russia by placing an order on our website.

conclusions

Lada X-Ray Cross receives 13.7 points out of 16 possible for protecting front seat belts from a frontal impact. This is 4 stars out of a possible four according to the ARCAP system from Autoreview magazine. It ranks 5th in the safety rating. Above are the Volkswagen Polo Sedan, Lada Vesta, Hyundai Creta and Solaris.

to experts, the results of the Lada X Ray Cross crash test are affected by the outdated French B0 platform. The body can withstand the blow, but without reserve, and the Koreans produce the next generation of bodies, which are more durable. On the other hand, the Brazilian-built Renault Sandero, the progenitor of the X-Ray, performed worse in the Latin American Latin NCAP rating - 8 points out of 16 possible. So the body received fines for violating the structural value; the base does not have seat belt pretensioners or limiters. Let's say thank you to the alliance for being more concerned about the safety of Russian car owners.

Product delivery options

Note! Below are the shipping methods available specifically for this product. Payment options may vary depending on the shipping method. Detailed information can be found on the “Delivery and Payment” page.

Parcel by Russian Post

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Shipping throughout Russia. Delivery time is from 5 to 12 days.

Parcel by Russian Post 1st class

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

Shipping throughout Russia. Delivery time is from 2 to 5 days. More expensive than regular delivery by Russian Post, approximately 50%. Parcel weight up to 2.5 kg

Express Parcel EMS

Available payment methods:

• Cash on delivery (payment upon receipt)
• Using cards Sberbank, VTB, Post Bank, Tinkoff
• Yandex money
• QIWI
• ROBOKASSA

CHASSIS

The front has an independent suspension with MacPherson struts, unified with the Renault Duster. Judging by the Duster, it’s reliable and inexpensive. At the rear there is a regular “beam” with springs and shock absorbers. In terms of driving performance, it is of medium hardness: it smooths out minor road irregularities and does not break through the struts in large potholes.

— It’s a bit harsh on 17-inch wheels. But it handles well. For comfort, “sixteenth” or even “fifteenth” with large tires is better. In the rear seats, passengers complain about excessive shaking on bumps, notes Evgeniy.

The ground clearance is 19.5 cm. This is enough for comfortable parking to the curb, and on winter ruts - without clinging to the bottom.

However, you can’t rely only on ground clearance - due to the lack of all-wheel drive and at least some off-road qualities, you can only drive off the asphalt if you are convinced that the ground is hard.

How to find out the engine coolant temperature on a Lada XRAY

October 17, 2021 LadaOnline 38 361 The Lada XRAY instrument panel is a modified Renault panel. The shield consists of three wells, one of which has an on-board computer built into it. One of the features of this instrument cluster is the absence of a coolant indicator. Let's look at several ways to find out the temperature of the Lada XRAY engine.

Diagnostic adapter ELM327

You can buy an adapter (price about 400 rubles) on Aliexpress (see product catalog). We insert the adapter into the OBD-II connector (see where this connector is), connect to it via a smartphone, and display the engine temperature value on the screen using special software. By the way, you can display the temperature on the screen of the radio, which runs on Android.

On-board computer

See the review of on-board computers for Lada XRAY (prices from 2850 rubles). We install it in any place convenient for you. Such devices allow you to display not only coolant temperature readings, but also a number of other engine parameters, as well as read and erase errors.

Universal engine temperature indicator (OBD2)

Connects to the OBD-II connector and displays the coolant temperature on a small screen. Some models, for example, from ELANG LLC Togliatti, additionally allow you to read and erase errors in the engine management system. The low price (about 800 rubles) and ease of installation make this device popular among Lada XRAY owners.

Universal engine temperature indicator (sensor)

In the Aliexpress catalog you can buy a universal digital thermometer for 150 rubles. Place the display in the cabin, pull the wire with the sensor into the engine compartment (through the hole where the hood cable passes), attach the sensor to the engine cooling system hose (photo from xrayclub.ru).

THAT. What and when to do

The list of maintenance work for the Lada X-Ray is quite extensive. But most of this work can be described as “tug, listen, check.” That is, such routine work includes such items as checking the level of technical fluids, diagnosing the suspension, checking play, tire pressure, lubrication of hinges and locks, etc. In general, everything that an experienced car owner does on his own during operation, and not waiting until the odometer shows 15 thousand km.

But in the first maintenance there is also work related to the replacement of some working fluids and consumables. So, during this service the following are subject to replacement:

• Oil and filter element;
• Air filter element of the power plant;
• Cabin filter;

It is also necessary to check the level of other technical fluids (and replenish them if necessary) and the condition of the brake pads.

During TO-2, which is done after 30 thousand km, the service center performs the entire list of TO-1 work, and also replaces the spark plugs. According to the list of works, TO-3 fully corresponds to TO-1, but in addition the brake fluid is replaced.

All maintenance work is repeated up to TO-6. When hitting 90 thousand km. In addition, the accessory drive belt along with the tension roller, as well as the coolant, require replacement.

It is worth noting here that even though the automaker indicates that the timing belt must be replaced at 180 thousand km, it is better not to reach such a mileage and replace it during maintenance 6.

As for technical fluids, except oil, they should also be changed every 3 years if the car’s mileage has not reached the required level.

Let's summarize. Every one must be replaced:

• 15 thousand km - oil and filter, if necessary - pads;
• 30 thousand km - spark plugs;
• 45 thousand km – brake fluid;
• 90 thousand km – drive belts with tension rollers (timing and attachments);

These are the main types of work, and they must be performed. All other maintenance is mostly carried out during operation.

Damage to shock sensors

Airbag deployment is dependent on the seat belt buckle and impact sensors. When they fail, a light comes on and remains on continuously.

A modern car is usually equipped with at least four shock sensors. They are placed in front to make the airbag more likely to deploy. If even one of them is damaged, the indicator lights up

In such cases, it is important to identify the specific sensor, repair or replace it

Control of the seat belt buckle is necessary so that when it is open, this device does not operate. Often the cause of lock breakdowns is water ingress when washing the interior. This error can be detected using a special diagnostic scanner.

For comparison

Volkswagen Polo. The hood, both headlights, bumper, crossbar with crushed elements, plastic radiator mounting box and air duct are damaged.

Hyundai Solaris. The bumper was cracked, the hood and fender were slightly dented, the headlight and fog lamp housing were destroyed, the front beam and the end of the left side member were damaged

Chevrolet Cobalt. The bumper cover is torn, both headlights are damaged, the front panel, crossbar, hood and left fender are deformed

Peugeot 408. The crossbar and replacement mounts of the left headlight are damaged, the bumper trim is slightly damaged

Renault Sandero. The front beam, engine subframe, front part of the left side member, top panel, front left fender and engine compartment mudguard were deformed. The left headlight is broken, the edge of the hood is dented, the front bumper is torn, the radiator mount is broken

Lada Granta. The radiator frame is crushed and torn, the hood, headlight, both wings, and spar are damaged.

Nissan Almera. The bumper lining was damaged, both headlights were damaged, the front panel, crossbar, side member, subframe, hood and left fender were deformed.

Skoda Rapid. The edge of the hood is jammed, the headlight, bumper trim, crossbar with crushed elements, radiator mounting screen, left fender, fog lamp are damaged.

Geely Emgrand. The hood, fender, amplifier and bumper trim, headlight, and transmission radiator were damaged. The front body panel, side member and mudguard of the engine compartment were deformed

Lada Vesta. The hood, cross beam with crushed elements, bumper trim, headlight, and radiator mount were damaged. The left fender was slightly damaged, the plastic bumper reinforcements and the receiver air duct were cracked

Removing and installing airbags

A disposable fabric ball is replaced with a new element after a collision. The ECU then stores an error in its memory. If the unit fails to reflash, then buy and install another component.

Passenger

The location of the device is the car frame, behind the dashboard.

The replacement goes like this:

1. They turn off the power to the car.
2. Remove the steering wheel cover and cushion, even if it is in good condition.
3. The steering wheel is removed.
4. Unscrew the bolts above the pedals and get to the center console.
5. Unclip the console clips with a screwdriver and remove the radio.
6. Remove the dashboard panel.
7. Disconnect the wiring and remove the pillow.
8. Install a new bag.

Then everything is assembled in reverse order.

Lateral

Work with the pyrotechnic module is carried out by trained personnel. Procedure:

1. Disconnect the battery.
2. Remove the front seat.
3. Dismantle the headrest and its guide bushings.
4. Remove the outer casing and inner panel of the front seat.
5. Remove the back panel and upholstery.
6. Remove the airbag.
7. Install a new bag.

Next, install the upholstery, back panel and other parts removed earlier.

You can check the correct operation only in an emergency situation, in the next accident. Therefore, the average driver should not take risks and change the fuel seal on his own.

Steering wheel cushion

The basic steps for removing the driver's airbag in the steering wheel are the same for all Lada Vesta cars:

1. First, disconnect the battery.
2. Next, unscrew the screws and release the pillow.
3. Disconnect the wire clamps and the block.

Steering wheel cushion. Photo source: https://www.drive2.ru/l/3006618/

Now you can remove the airbag from the Vesta steering wheel and install another one. To do this, continue working in reverse order.

Sometimes after an accident, drivers do not want to install a new passive safety device due to the high price (12-20 thousand rubles) or other reasons. To deceive the ECU, they resort to a dummy. A time relay is connected to the fake steering wheel cover, which de-energizes the light bulb 5-7 seconds after the engine starts. The snag costs from 2,500 rubles.

Cost of restoration at a service station

Repairing a Lada X-Ray at a service station will cost less. This is due to the fact that such services do not always replace damaged elements, because some of them can be restored. For example, why buy a right headlight if you can glue the “ears” of the mount back. Also, with the help of straightening, it is quite possible to restore the geometry of the cross member, beam, front part of the spar, and return the radiator to its place. And this significantly reduces costs. Note that some craftsmen, using special equipment and tools for straightening (a slipway, a spotter, a reverse hammer, etc.), can also restore external elements that have been damaged - the hood, the wing.

Even if the service station decides to replace the external elements, it will still be cheaper and you will have to pay about $1000 for spare parts. In addition, at such a service station they will charge less for the work - approximately $750-800. The only drawback of repairs at a universal service station is the fact that some parts are restored by straightening and not replaced. Such elements, no matter how the geometry was restored, have already lost their strength. Therefore, in the event of a second collision, the damage will be more significant.

The Lada X-Ray crash test video below will provide detailed information about the damage received.

Repair at the service center. Price

The service center usually replaces all damaged elements. And this, in turn, affects the cost of repairs, as well as time, because you often have to wait for the delivery of spare parts. From the damage listed above, you can understand which elements will need to be replaced. We will immediately indicate the cost of each part. So, to restore a car you will need:

• Hood ($185-210);

• Headlights 2 pcs. ($625-710);

• Left wing ($75-90);

• Cross beam ($210-250);

• Upper crossbar ($150-175);

• Front spar ($170-$190);

• Bumper ($165-280);

• Radiator grille ($20-25).

In general, you will have to spend from $1,600 to $1,930 on spare parts (it all depends on the suppliers). You will also have to pay the service for restoration - replacing damaged elements, editing some of them, painting work. The total cost of the work will cost about $850. In total, restoring a Lada X-Ray to its original condition in the event of such a minor collision will cost $2,450-$2,780 in service. And this is with the price of the car itself being $10,380-$13,850. That is, for restoration you will have to pay almost a quarter of the cost of the crossover.