Front bumper for VAZ 2115 - replacement, repair, how much it costs

The bumper has now become an integral part of the body of any vehicle. It not only completes the appearance, but also performs a completely utilitarian function - it protects the car from minor damage. During a collision, it usually breaks, due to which the inertia of the impact is partially absorbed.

Older car models have metal bumpers. Consequently, this fact led to the fact that the car received much greater damage upon impact. This caused significant damage not only to the vehicle itself, but often to the people sitting in it. Modern bumpers are made of plastic or synthetic resins - they are softer and perform their role perfectly. There is, however, one significant drawback - after a collision, most likely, it will have to be replaced.

When does it become necessary to remove the bumper?

In reality, it is a rare car owner who can boast that he has never had to remove the bumper himself in his life. This is usually required in cases where:

The power unit is being repaired;
a new radiator is installed;
a decorative grille is installed;
The damaged front (or rear) bumper of a VAZ-2115 is being replaced.

It is worth noting that if this element of the car was damaged, the owner can either buy a new one or try to repair the old one.

We'll tell you more about the repair below.

conclusions

Removing and installing the front bumper on a VAZ-2114 is quite easy and even a novice motorist can handle this process, the main thing is that there is a desire and hands grow from the right place. Well, if the process described in the article seemed very complicated, then you need to contact a car service, where they will do everything for an immodest fee.

Independent replacement of front and rear bumpers on VAZ 2113, 2114, 2115

On VAZ 2113, 2114, 2115

plastic bumpers are installed.
How to remove and replace the front or rear bumper from VAZ 2113, 2114 and 2115 cars. Video and manual on removing and replacing rear shock absorbers and springs on VAZ 2113, 2114, 2115 - do-it-yourself car maintenance and repair. During use, this part may be damaged due to collision. In case of severe damage, the rear bumper
is easier
to remove
and replace than to repair, and this can be done without the help of others.

How to choose the right new bumper

Nowadays, stores sell not only products produced directly by VAZ, but also many replicas manufactured by various companies.
Quite handicrafts are also often found. To avoid purchasing low-quality goods, you need to use the following recommendations:

the thickness of the plastic should be the same as the old one, or better yet, even greater;
It is important to guess the shade if it is sold already painted.

Of course, no one forces the car owner to replace a damaged bumper, but it significantly spoils the appearance of the car. Moreover, if another accident occurs, then he will no longer be able to protect anyone or anything.

Removing the bumper

To do this you will need the following tools:

Phillips screwdriver;
socket wrench 10/8;
end at 13.

Usually the procedure takes no more than an hour. To make the replacement more convenient, it is better to install the car in a pit.

To dismantle the bumper you will need to perform the following steps:

move the protection away from both front wheels, having previously unscrewed the fixing screws;
use a 10mm wrench to tighten the nuts located inside the bumper (there are 4 of them in total, 2 on each side);
dismantle the license plate;
unscrew the bolts hidden under it and located below, in special openings;
Then the protective element itself is removed.

If it turns out that the amplifier has also become unusable, it will need to be replaced with a new one. It is held in place by two nuts, unscrew them using a 13mm wrench.

Now all that remains is to move both side brackets from the old to the new. They are secured with three screws each.

It is important not to forget to adjust the amplifier. There should be a gap between it, the headlights and the fenders. This is not difficult to do, since there are special slots on it.

Rear bumper

Dismantling

Remove the rear wheel fenders.
Use a metal brush to clean off dirt, grease, and oil, and inject VD-40 aerosol while working.

How to repair a bumper

If the damage is minor, then there is no need to spend money on a new element. The following defects can be eliminated independently without problems:

dents;
scratches;
small holes.

It would be advisable to repair only a bumper that has not lost its integrity. Now stores sell special kits that include everything you need.

Cracks and holes are fixed on the reverse side with fiberglass and liquid plastic. Next you need to sand the damaged areas with coarse sandpaper. This should be done without much fanaticism, so as not to damage the plastic. The defect is masked with universal putty. The surface is lightly sanded again, but with very fine-grained sandpaper. Afterwards you need to wipe with a damp cloth - this will remove dust.

The prepared surface is treated with an aerosol primer. It must be applied in two layers. Each will take half an hour to dry. Finally they are coated with paint. At least 3 coats will be required. It is important to choose it exactly by color. A single coat dries completely in about 30 minutes. In order for the composition to be sprayed evenly, the container must be kept at a distance of 20 centimeters.

The result is fixed with two layers of colorless varnish.

You can learn more about the process of dismantling the bumper using this video:

Standard front bumper VAZ 2113—2115

In accordance with the general trend, on Russian-made VAZ 2113–2115 cars, bumpers made of plastic and painted in the color of the car are installed. These are the most vulnerable body elements, located low above the road surface and taking on all kinds of mechanical loads. The front body kit suffers especially, where stones often fly from under the wheels of oncoming traffic, which is why parts have to be removed for repair or replacement. But thanks to the simplicity of the design, any motorist with the time and desire can handle the removal. Let's consider the task of removing the front and rear bumpers using the example of the VAZ 2114 and analogues.

Video review of the procedure for removing and installing the front bumper of VAZ 2113 / 2114 / 2115

–>

Welcome! The rear bumper is one of the main things that is the very first to be hit when any passenger car hits from behind, so the bumper as such is a consumable item in almost any accident, because basically it’s always only the bumpers that suffer, but not many people know how to replace them . Today we have prepared an article especially for you that will describe in detail the process of replacing the rear bumper on cars of the Samara family.

Note! To replace the rear bumper, you will need to stock up on: A basic set of wrenches, and also need a screwdriver to unscrew the bumper covers and license plate if you have one (Applies only to the VAZ 2115 car), and also take a rag with you to wipe completely bumper and work with clean (At your discretion)!

Summary:

How to attach the bumper? On Samara 2, the bumper seems to be installed on the same cars, but in fact it can be mounted completely differently on the same cars, the whole point is that there are two types of protection with which the rear bumpers are installed on the car , let's look at it in more detail:

The first type of protection is the rear bumper with a plastic beam, it is secured with two bolts at the end of which there are nuts.

The second type of protection is a rear bumper with a reinforced metal beam, its fastening is almost the same as that of the first type of protection, namely, it is attached to the sides of the car body using three fastening bolts.

Why remove bumpers on VAZ 2113-2115

What kind of “blows of fate” do the front and rear body kits experience during operation? Either a stone will fly, then someone in the parking lot will catch it and scratch it, or even the driver himself will drive into a snowdrift where an iron pipe is hiding. Not to mention such little things as traces of insects crashing on the front. Some of the listed defects can be eliminated without removing parts from the car, but in case of serious damage, dismantling is inevitable.

Such damage cannot be repaired, the body kit is easier to change

A separate story is a collision during an accident, as a result of which the bumper often turns into outright trash, unsuitable for repair. Fortunately, spare parts for Russian cars are freely available and their prices are quite affordable.

Reference. The cost of the front and rear body kits is almost the same and starts from 2,600 rubles. for an unpainted part. Prices for products with color coating start from 3,250 rubles.

The main reasons why owners of the “thirteenth” and “fifteenth” VAZ models have to dismantle the bumpers are as follows:

It is necessary to completely repaint the car and perform body repairs.
To repair or replace a broken body kit.
It is easier to install fog lights on the removed front element.
You need to get to other body parts located under the bumper.
It was decided to throw away the stock factory body kits and install beautiful elements of the original shape, that is, to do partial styling of the car.

This is what the VAZ 2115 styling front body kit looks like

Note. To this day you can find budget black bumpers on VAZ 13-15 series cars. The owners of these cars, as soon as possible, remove unsightly parts in order to paint them in the desired color or replace them with painted ones.

The first 2114 models came with black body kits

What is important to know when purchasing new products for VAZ 2113, 2114 and 2115

Unlike foreign-made cars, it is easy to buy the necessary spare parts for the VAZ 2113, including new bumpers. In the retail chain, these parts are found in two forms:

black, without painting;
painted in any color of your choice.

Body kits of different colors and shapes

Advice. If you decide to change body kits because of their unpresentable appearance, then it is easier and cheaper to buy ready-made products painted in the color of the car. The difference in price is 700-900 rubles. will not allow you to save a significant amount on painting a black bumper.

Unpainted parts are usually taken during a major body repair with full painting or in the case of repainting the car in some individual color. It is also appropriate here to remember those owners whose cars were equipped from the factory with unpainted elements, which, if they break down, are easily replaced with similar ones.

Standard front bumper VAZ 2113—2115

When choosing a new bumper for VAZ 2113 (2114, 2115), consider several recommendations:

There are several manufacturers on the market that use various raw materials, including recycled ones, to produce plastic body parts. Therefore, when purchasing, pay attention to the elasticity of the plastic. If it is initially rigid, then at negative temperatures it will become very brittle.
Before purchasing a new product, remove the old body kit to check the condition of the amplifier underneath. If the disassembly was caused by the plastic breaking due to an impact, then the amplifier could also be damaged. In addition, it will be possible to compare the factory bumper with the part offered in the store.
Check the element for minor paint defects. It happens that plastic parts are damaged during transportation.
If you notice that the design of the new bumper is additionally reinforced from the inside, then buy it with confidence, since such products are more reliable in operation.
Please note that there are openings for installing fog lights. There are products on sale for the VAZ 2114 that are not equipped with holes.
When purchasing, make sure that the items fit your car in size. You should not purchase bumpers for a VAZ 2115 from a VAZ 2114 and vice versa, since they differ in dimensions, although they are mounted in the same way.

Factory bumper VAZ 2113—2115

Wanting to give their cars individuality, their owners often do partial styling, replacing the stock (factory) body kits with more original and attractive ones that differ in shape. As a rule, such elements can be easily installed on standard mounts and do not require modifications.

Reference. The prices of serial styling bumpers are not much higher than stock ones and start from 3,500 rubles. (for an unpainted product). Original works can cost significantly more.

The rear styling kit looks impressive

How to remove the front bumper on a VAZ-2114 to replace it: useful tips and videos

Some motorists were faced with the fact that they had to change the front bumper on a VAZ-2114. This could be due to the fact that its structure was destroyed or the structure itself was altered. Of course, I had to go to a car service center, where they charged quite a lot of money for such a simple process. This article tells you how to change the front bumper with your own hands.

How to remove the 2114 bumper from the front of the body

Before removing the front bumper on a VAZ 2114, it is advisable to familiarize yourself in detail with the step-by-step instructions for performing the work. Agree, there is no need to go to a car repair shop and involve other specialists in performing the work if removing the front bumper of a VAZ 2114 can be done independently in a personal garage in a fairly short time. After all, the whole job will take no more than one hour.

Remove the front protective and decorative element of the machine according to the following algorithm:

First, we independently remove the wheel protection, which is secured with self-tapping screws. To do this, use a screwdriver to unscrew 3-4 screws securing the front fender liners;
then we remove the wheel arch liners and free access to the inner surface of the bumper. Next, you will need to unscrew two locking nuts 10 on each side of the bumper. It is necessary to pull each side of the bumper so that the mounting studs come out of the holes in the brackets;
You will also need to remove your license plate number. After all, under it there are two 10mm fixing bolts. They will need to be unscrewed, as well as a couple of screws located in the cavities under the license plate.

READ Replacing the cabin filter Grand Vitara

Don’t forget to disconnect the fog lamp wires, remove the trims and unscrew the headlight mounting screws if they are attached to the car’s bumper. After performing these operations, all that remains is to carefully remove the front without applying much effort.

The bumper on a VAZ can be removed without much effort

After dismantling the bumper, check that there is no deformation on the metal amplifier. If there are cracks or dents, the amplifier will need to be restored to its previous condition by welding, straightening or replacement.

To replace the amplifier, you will need to unscrew the fastening nuts with a 13 mm socket. After restoring the power bracket, its position should be adjusted to the required height, ensuring equal gaps between the wing and the reinforcement bracket. The grooves make it easy to complete the task.

Design Features

The design and method of attaching body kits on Lada 13-15 series cars differs from other models of the “tenth” VAZ family. Design features are as follows:

Additional metal brackets for fastening to the body are installed inside the plastic elements;
the brackets are held on by threaded connections and screwed to the bumper with self-tapping screws;
plastic latches appeared on the central part of the front bumper;
the edges of the rear body kit are pulled to the body by nuts hidden behind the wheel arches;
It is easier to remove the front and rear parts together with the amplifier, and then unscrew it if necessary.

Front bumper design

The listed features make it somewhat difficult to dismantle elements from the machine, since the threads located next to the wheels become covered with dirt and rust during operation. Over the years, corrosion also eats away at bare metal brackets that are not protected by any coating.

The rusted bracket needs to be replaced

Hence the advice: when disassembling, take your time and do not apply much force, otherwise you will break the bolts. It is better to replace rusty brackets with new ones, but they must first be coated with a primer and painted in any color.

Removal stages

To carry out dismantling, you do not need to resort to the services of specialized lifts. Ordinary jacks can easily cope with the assigned task. Removal of the rear bumper of the VAZ-2114 begins by placing the car on a flat surface. Then you should support the front wheels with stops and raise the rear part of the body with jacks.

The next item is removing the wheels. This opens up access to the fender liners, which will also need to be removed. This is also a good opportunity to clean out the dirt that has accumulated there. Therefore, it will not be superfluous to additionally stock up on a brush.

Next is the turn of the license plate lighting system. All electrical wiring is disconnected and the lamp itself is removed. After this, you can detach the license plate itself.

After this, you can begin to directly dismantle the spare part itself.

The nuance here is that attaching the rear bumper of the VAZ-2114 to the car body is carried out in several stages and in order to remove the part, a certain sequence is necessary:

READ Replacement of cylinder head gasket VAZ 2115 8 valves

Removing the 2 linings that secure the spare part (a 10 mm wrench is required).

Unscrewing the 3 bracket nuts holding the reinforcing beam.
Removing the freed bumper.

With regard to the first point, it becomes clear why it was necessary to remove the fender liners - the nuts securing the linings are located in the wheel arch, and it will not be possible to get to them without removing them. Do not forget to lubricate all fixing elements.

Upon completion of the dismantling work, you will have a bumper in your hands with an amplifier screwed to it. If desired, these two elements can also be separated, since they are held on by ordinary screws.

Important! Do not rush to throw away the reinforcing beam if there are no signs of damage on it; perhaps in your situation, repairing the device will be preferable to replacing it.

Instructions for dismantling the front body kit with your own hands

To disassemble the bumper mounts you will need the following tool:

Phillips screwdriver;
8 mm socket wrench;
the same, size 10 mm.

Disassembly tool

Advice. Instead of separate keys during disassembly, it is more convenient to use heads with an extension and a wrench equipped with a ratchet.

It is more convenient to work with sockets and a ratchet wrench

Since most threaded joints are likely to be rusty, you will need to use WD-40 spray lubricant to rotate them. Apply it to all bolts and nuts before unscrewing.

It is more convenient to work with the lower mounts of the front body kit from the inspection ditch, from where they are clearly visible, although if necessary, you can dismantle the bumper without a pit. At the final stage, when the element is removed from the machine, it is worth having an assistant support the part by the second edge.

If the car is equipped with fog lights, the process begins by disconnecting the battery from the on-board network. Further work is performed in the following sequence:

Open the hood and use a screwdriver to unscrew the 4 screws holding the upper part of the radiator grille. Remove it from the car.
The lower part of the radiator grille is held in place by 4 self-tapping screws - a pair from the outside and two more from the engine compartment. Unscrew them and remove the grille part.
Unscrew the 6 screws of the lower body kit mounting. They are located on the rounded parts of the element, 3 on each side.
Remove the plastic protection installed under the wheel arches by unscrewing the bolts and nuts with a 10 mm wrench. For greater convenience, you can remove the wheel. Unscrew the front part of the fender liner.
Now you have access to the bracket, where you need to loosen and unscrew 2 10 mm nuts. Don't forget to treat the joints with WD-40.
Remove the license plate, underneath it you will find 2 more front mounting bolts. Unscrew them, as well as the 2 screws located near the air intake opening.

After disassembly, you will see plastic latches on the horizontal plane of the body kit. Unlock them and, together with an assistant, remove the bumper from the car, pushing it forward and holding it on both sides. Before doing this, disconnect the power wires for the fog lights so that you don’t have to do it while hanging.

Note. After dismantling the element, access to the plastic amplifier mount will open. If it is damaged and needs to be replaced, you need to unscrew the 4 nuts with a 13 mm socket and remove the part from the studs.

If you need to install a new body kit instead of a broken one, then you need to twist the metal brackets from the latter. To do this, just unscrew the 3 fastening screws. The brackets themselves should be cleaned of rust and painted so that they do not rot prematurely. The bumper is installed in the same way, only in reverse order.

The order of work in the photo

3 screws for bottom fastening

This is what the side bracket looks like

The top panel above the radiator is held on by two screws

Video about disassembling the front part of the car

Front bumper

Replacing the front bumper of a VAZ 2114 with your own hands takes a little time. If it is necessary to replace the radiator or grille, the procedure takes longer. Removing the body kit for all VAZ 2113-2115 models is carried out in the same way.

Tool

To replace the body kit you will need the following tools:

Screwdriver Set;
open-end wrenches 8 and 10 mm;
13 mm ratchet head with crank.

Step-by-step removal

To remove the front bumper of a VAZ 2114, place the car on a viewing hole or a lift. The algorithm for dismantling the body kit is as follows:

The electrical connections to the license plate and fog lights must be turned off before any work can be done.
The fastening bolts and nuts are treated against rust, as well as for better loosening, with VD-40 aerosol.
Unfasten the front wheel fenders.
Unscrew the fender liner mounting plate with a 10 mm wrench.

Remove the 3 screws that are attached to the body kit.
Using a 8 key, remove the 6 screws securing the fender liner to the front fender.

Pull back the fender liner.
Remove the radiator and headlight trims.

Using a 10 mm wrench, unscrew the 2 nuts securing the left side of the bumper.
Pull it a little to the side so that the studs come out of the body bracket.

How to remove the rear bumper

To replace the rear body kit, an inspection ditch is not needed, since there is fairly easy access to the lower nuts and screws. But the set of necessary tools will have to be supplemented:

13 mm head;
jack;
wheel wrench;
wooden stands for the rear wheel hubs.

Advice. It doesn’t hurt to stock up on a brush with metal bristles to clean the fasteners from dirt or anti-corrosion coating.

The problem is that with the wheels installed, it is difficult to get to the threaded connections located on the back side of the wheel arch. Therefore, before carrying out work, you need to secure the car at the front with wheel chocks and remove both rear wheels, resting the hubs on stands. The next procedure is as follows:

Remove the plastic wheel arch protection by unscrewing the screws holding it. Perform the operation on both sides.
Looking under the back of the arch, you will find 2 studs with tightened nuts. Treat them with a brush and WD-40, and then unscrew the socket 10 mm. Remove the plastic trim. Repeat on the other side.
Loosen and unscrew the 4 13mm socket nuts that secure the bumper reinforcement to the steel body parts. They are located under the body kit in pairs.
Together with an assistant, grasp the edges of the bumper, remove the side mounting studs from the holes and remove it by pushing it backwards.

Note. In this way, the part is removed along with the amplifier. If you want to dismantle only the body kit, you will have to lie under the car to unscrew the 4 mounting screws, which is inconvenient.

When the element is removed from the car, it is easy to dismantle the amplifier and brackets and move them to a new bumper. There are no electrical wiring or lampshades here, so you don’t have to disconnect the battery or disconnect the connectors.

With the rear body kit removed, the condition of the steel body elements is clearly visible. If you find traces of corrosion, then there is no better time to remove it and touch up the paint. Pay attention to the condition of the side bumper mounting brackets; replace them if necessary. The element is placed back together with an assistant, the task is to simultaneously insert the studs into the holes of the arches. You can tighten the nuts and screws in any order; at the end, put the protection and wheels in place.

Photo instructions for dismantling

It's difficult to get to the mounts without removing the wheel.

Amplifier mounting screws, 4 in total

The body kit mount is hidden behind a plastic protection

How to change the rear aero without any problems - video

For car service specialists, replacing bumpers on VAZ 2113–2115 cars will take a maximum of an hour. The owner of the car will need twice as much time to disassemble it independently, but will be able to save at least 2,000 rubles on the cost of work. Hence the conclusion: it is not advisable to contact a car service center with such questions, unless you do not have the required amount of time.

How to replace the rear bumper on a VAZ 2113-VAZ 2115?

Note! Before you begin removal, be sure to remove the fender liners from the car! (For information on how to remove them, see the article entitled: “Replacing wheel arch liners on a VAZ”)

Removal: 1) First, be sure to disconnect the wires from the light that illuminates the car’s license plate, and after disconnecting the light, unscrew the screws that secure the license plate and remove it from the car’s bumper.

2) Next, using a wrench, unscrew the two nuts that secure the bumper trim to the car body. (These fastening nuts are located in the wheel arch, so after removing the wheel arch liner, look there and unscrew these nuts)

Note! There are three fastening bolts on a bumper with a metal reinforced beam, so unscrew all of them and then remove the rear bumper from the car!

3) Now, putting the wrench aside, take a screwdriver in your hands and use it to unscrew several screws that secure the same trim to the rear bumper.

4) After all this, carefully remove the trim from the side of the car bumper, but after this trim is removed from one side part, move to the other side and remove the same trim there in the same way.

5) Then pull the bumper to the rear and thereby completely remove it from the car.

Note! When the rear bumper is removed from the car, it will be removed together with the beam, because it comes assembled with it, so if you want to disconnect this beam and install it on the old bumper, then take a wrench in your hands and unscrew all the nuts that attach the beam to the car bumper!

Installation: Installing a new bumper on the rear of the car occurs in the reverse order of removal.

Note! When you install the bumper, be careful not to damage it, otherwise you will have to either change it, paint it, or leave everything as is!

Additional video clip: You can find out more about how to change the bumper on the rear of the car in the video clip located just below:

Home / Catalog / Lada / Lada / VAZ 2113 / VAZ 2114 / VAZ 2115 with 1.5i liter and 1.6i liter engines, repair book in color photos in electronic form / ...Show book contents

Content

Introduction

Emergency procedures

Wheel replacement
Actions in case of engine overheating
Starting the engine from an additional power source
Circuit breakers
Emergency pressure drop in the engine lubrication system
Turning on the low battery indicator
Turning on the engine system malfunction indicator
Turn on the brake warning light/parking brake warning light

Daily checks and troubleshooting

Operating a car in winter

A trip to the service station

Operation and Maintenance Instructions

Technical information
Controls, instrument panel and interior equipment
Car care
Vehicle maintenance
Fuels and lubricants

Warnings and safety rules when working on a vehicle

Basic tools, measuring instruments and methods of working with them

Basic set of necessary tools
Methods of working with measuring instruments

Engine and its systems

General information
Servicing the engine without removing it from the car
Engine disassembly and assembly
Ignition and engine control system
Supply system
Lubrication system
Cooling system
Intake and exhaust system
Chapter Appendix

Transmission

General information
Clutch
Transmission
Drive shafts
Chapter Appendix

Chassis

General information
Front suspension
Rear suspension

Steering

General information
Steering wheel
Steering gear
Steering rods

Brake system

General information
Car service
Front wheel brakes
Rear wheel brakes
Parking brake

Body

General information
Front bumper
Rear bumper
Hood
Front door
Rear door (VAZ 2114/2115)
Body dimensions

Gas equipment

Car electrical equipment

General information
Generator
Starter
Egnition lock
Replacing steering column switches
Replacing the power window switch
Outdoor lighting devices

Fault codes

Controller JANUARY-4
GM Controller (IFSI-2S, ITMS-6F)
OBDII protocol controllers

Electrical circuits

Dictionary

Useful tips for car owners

How to pay and download

How much does a bumper (rear and front) cost for a VAZ 2115

The cost of a VAZ 2115 bumper varies from 2,125 to 8,500 rubles . This price includes products made of plastic, fiberglass and ABS plastic, which can be installed on the front and rear of the car without making changes to the power structure.

The bumper on the VAZ 2115 is an energy-absorbing part of the power structure , which prevents damage to the engine compartment in minor collisions. All proposed bumpers are installed on standard mounting locations, without moving the mountings and mounting brackets. Thus, the entire installation process takes no more than 20 minutes.

In addition to positioning the VAZ 2115 bumper as part of the load-bearing structure, it is a hinged body element with thoughtful geometric proportions and internal reinforcements. This allows you to move among tall grass and small branches without any problems. The bumper provides comprehensive protection, both through the front overhang and central points, from damage to the head lighting equipment.

The rear bumper of the VAZ 2110 performs similar functions. It already has standard holes for installing a towbar, as well as a 12 V socket on its front panel. Given the limited size of the power structure of the rear of the car, the bumper is also small. This is also reflected in its cost, which is usually 20-25% lower than the front one.

How to replace a bumper VAZ 2114 2115 2113

The VAZ bumper is an energy-absorbing device in the form of a bar, located in the front and rear parts of the Lada Samara 2 car. This important safety element is a mandatory part of the body and gives the car a beautiful appearance.

Body kits have 2 functions:

Decorative. The car looks more improved. The manufacturer developed inflated body elements as styling for the VAZ 2114. They look aesthetically pleasing and at the same time increase downforce when driving at high speeds, which improves safety.
Protective. The bumper protects the car from light impacts and damage, protects the reinforcing beam, body and other parts.

VAZ 2113/2114/2115 models are equipped with 2 bumpers:

in front of him;
rear

Body kits are made from 2 types of plastic material:

thermoplastic;
thermosetting.

Thermoplastic plastic can be easily softened and is combined into a homogeneous structure during repairs. Thermosets cannot be repaired by welding.

The material marking is located on the inside of the body element.

As the vehicle is used, various collisions and obstacles may occur, followed by deformation of the body kit. Replacing the front bumper of the VAZ 2115 in this case is mandatory.

If you leave the damaged part, then with a possible next impact, all the energy will be directed to the car body, as a result of which many mechanisms will fail:

radiator, its grille;
fan;
wheel arch liners

In case of minor damage, such as scratches, small cracks, the body kits can be glued, puttied and painted. The reasons for removing this part are as follows:

deformation of an element as a result of a collision or impact;
engine repair, reinforcement beam, radiator replacement;
installation of a protective mesh, decorative lining;
replacement of headlights, installation of optics.

The rear body kit of the VAZ 2114 differs from the front one in the absence of holes for the vehicle registration number.

The reasons for repairing and replacing the rear bumper of a VAZ 2114 are the same as for the front element:

integrity violation;
body deformation;
chips, cracks.

What affects the price?

In addition to the brand under which the front and rear bumpers on the VAZ 2115 are manufactured, the key pricing factors are:

Material.
Mode of production.
Type of product (standard, modified, sports).
The bumpers are equipped with nets, edgings/plugs for DRLs, and PTF.
Type of spare part (original, analogue).

The price is also affected by the completeness. Thus, an increase in the retail price is noted as the following elements are included in the kit: a seal between the bumper and the power beam, new fastenings to the body, internal fasteners, hidden wiring elements (connectors, pins, etc.).

The cheapest sets of front and rear bumpers are considered to be those that
can be painted . Such bumpers are supplied in rough form or, if this is a sporty version for external car styling, in gray shipping primer for grinding. It is worth noting that painted elements may not match in shade and there is a possibility of damage during transportation.

When to install a new part

If the bumper is damaged, it is not always possible to return it. How to remove the front and rear bumper T5)))?? on the sides and one in the middle as well. If there are small cracks and scratches, the part can be repaired according to the car service criteria. If the bumper

If it just splits into several pieces, it won’t be possible to return it. In this case, there is only one way out - change the part. how to install the camera. rear view camera on the Granta REMOVING THE BUMPER on the Granta. Depending on the extent of the damage, bumper mounts may have to be repaired from time to time.

Original VAZ 2115 bumpers and how much do they cost?

There are more than 47 colors to choose from in which VAZ 2115 cars were produced, but the most popular items turned out to be the following:

Front bumper according to catalog number 2115-2803015-00 (color 660 Altair) – RUB 3,900 .
2115-28084015-00 (281 Crystal) – 3,510 rub .
2115-2806015-00 (426 Muscariy) – 3,270 rub .
Rear bumper, 2115-2804015-00 (regardless of color) – RUB 3,240 .

The price of the product may vary in the range of 400 rubles , since some colors were produced in limited quantities. The cheapest colors are gray and white. The appearance and design features are unchanged.

Analogs of VAZ 2115 bumpers and their price

Bumper analogues are designed for exterior car styling using a minimal set of tools. Among the certified analogues that do not affect the issuance of a technical inspection sheet or other documents are:

I Robot (front, large radiator grille, increased lower overhang) – 8,500 rubles .
AVR Cup (front, 32″, under a sports hood) – 8,500 rubles .
Fan-2 (front, without changing other body elements, choice of car color) – RUB 6,190 .
Nevada 239 (rear, with metal amplifier, painted) – RUB 4,316 .
Cosmos 665 (rear, with molding for the socket platform) – 4,600 rubles .
2115-2804015-32 (rear, for AL amplifier) – RUB 3,423 .

Where can I buy?

Bumpers for the VAZ 2115 can be bought at any store, especially if we are talking about non-original versions. If this is a fiberglass bumper, then it is important to pay attention not only to the final priming, but also to the amount of putty used. The latter should contain particles of ceramics or aluminum shavings.

If the goal is to save money, then you can give preference to bumpers for painting yourself. Their price is 25% lower, but the quality remains the same.