Cruise control and speed limiter on Lada Vesta cars

DIY installation and connection instructions for cruise control

This device is not installed on all cars from the factory; for example, it is not available on some Lada models.
You can install the system on the Lada yourself (the author of the video is Juzef Gorodecki). Two types of universal kits with E-gas are popular:

1. Jet Cruise. Controlled using a key fob. Thanks to the system, the throttle valve is held in a predetermined position. Speed ​​depends on the terrain.
2. Drivenge. Control is carried out by the steering column switch. In cruise control mode, the system controls the throttle position depending on the road surface.

Installation of the Drivenge kit consists of installing the block and control lever. We install the block under the panel or seat. The lever with control buttons is installed on the steering casing on the left or right. For installation, drill the necessary holes. The connection is made using connectors in the gas pedal gap.

We connect the four wires as follows:

• black for ground (to any body part);
• red to the ignition switch;
• yellow to the speed sensor;
• brown to the brake pedal sensor.

If a manual transmission is installed, the green wire must be connected to the clutch pedal. If automatic, then the wire does not need to be connected anywhere.

Price issue

You can save on installing the device if you purchase the kit yourself and install it according to the instructions.

Loading …

Installing cruise control on a Lada Vesta Classic car

The fuel pump on the Lada Granta does not work.
How to replace the fuel filter on a Lada Kalina with your own hands. installation of a new fuel pump mesh On Vesta cars in the classic configuration, you can install a speed control function. This is done by connecting a multifunction steering wheel, which has the necessary keys to control the program.

This additional equipment is connected in the following way:

• Before starting work, disconnect the negative wire for safety reasons.
• Remove the plastic steering wheel cover by screwing in two screws at the bottom and the airbag
• Disconnect all wires and remove the steering wheel. It is pressed very tightly onto the cone, so it is not easy to remove
• We put on a new steering wheel and connect the wires back.
• We pull three cruise control wires through a special hole above the pedals and insert them into the block of the electronic control unit, which is located in the engine compartment
• We connect the wires according to the diagram:

To carry out such a conversion, you need to buy several spare parts, namely:

1. Multifunction steering wheel or steering wheel pad with buttons
2. “Snail” as in the Lux package
3. Wires with chips to the ECU

A set of these parts can be purchased in specialized stores. The estimated price as of August 2021 is 9,000 rubles. If you want cruise control data to be displayed on the dashboard, you need to flash the control unit, which will cost about 2,000 rubles.

Reviews about the operation of cruise control on Vesta

How to install multifunction steering wheel on Vesta

Tire pressure for Lada Vesta 16: what should be the pressure in Lada Vesta tires » lada.online

In addition to the steering wheel itself, you will need several small elements:

1. A special blue mini-ISO connector labeled C3.
2. The contact connector for the snail is BLS.
3. 5 pieces of wire 3 meters long with a cross-sectional diameter of 0.5 mm. But it’s better to buy a ready-made wiring harness so that connecting the multifunction steering wheel is convenient.

Tools and materials required to connect the multifunction steering wheel to the radio:

1. Insulating tape.
2. Several types of screwdrivers, nails and knitting needles. Such a tool may be required to remove the airbag.
3. Torx bit T50 (TORX). The multifunction steering wheel is secured with a bolt with the same type and size of head. It is difficult to unscrew the bolt with another wrench.

Installing a multifunction steering wheel on Vesta “Lux” configuration is more convenient. It has wires for connecting the cruise control system, a “snail” (a switch under the steering wheel with wires for the buttons). This is easy to check. You need to remove the top half of the steering wheel cover and see what's there.

You can install the multifunction steering wheel on Vesta only with the ignition switch turned off. In addition, it is recommended to disconnect the negative cable from the battery. Otherwise, you risk short circuiting the wiring.

Installing a multifunction steering wheel on Vesta in Comfort and Luxe configurations

Vesta and Vesta Cross differences: what is the difference between Lada Vesta and Vesta Cross: comparison, which is better

The multi-steering wheel on Vesta is only available in the Multimedia option package of the Comfort and Luxe trim levels. Owners of luxury cars are luckier, because... on these versions of cars there is partial preparation for connecting steering wheel buttons. The Lada.Online website was the first to compile detailed instructions for installing a multi-function steering wheel on Vesta in more affordable trim levels (Classic and Comfort).

We check that the steering column switch (volatile) has a connector for connecting the block with wires (photo No. 2 below), as well as the presence of a gray bundle of wires going into the steering wheel (photo No. 3 below). To do this, you need to remove the upper part of the plastic steering wheel cover (photo No. 1 below) by removing the two Torx screws from the bottom. And then, looking for gray wires, look between the steering wheel and the casing (or remove the airbag):

• If there are gray wires for the buttons on the steering wheel (they should be on the “Lux” configuration), then modification will not be difficult (there are separate instructions).
• If there are no wires (they were not found on the “Classic” and “Comfort” versions), then the modification will be a little more difficult (more on this later in the article).

How much does a multifunction steering wheel cost on a Lada Vesta?

Changing the pump to a Lada Granta with your own hands

The cost of such a mini steering wheel for Lada Vesta in different online stores may vary. You should be aware that the multifunction steering wheel, the price of which is from 5.5 to 6.5 thousand rubles, can be with or without an airbag. For this you will have to pay an extra couple of thousand rubles. If you want to reupholster the steering wheel with genuine leather, it will cost an additional 2 thousand rubles. You can buy the Lada Vesta multifunction steering wheel in many online stores, as well as in large auto markets.

If buying a multifunction steering wheel is an expensive pleasure for you, then an alternative option would be to install an overlay with buttons. Such a device is cheaper, but connecting a pseudo multifunction steering wheel to the radio will be difficult. Therefore, it is easier to buy a Vesta multifunction steering wheel than to install and connect the buttons yourself. By the way, if you decide to buy a multifunction steering wheel for Vesta, then write down the article number - 8450006832. This will make it easier to search in catalogs.

Cruise control "Jet-Cruise VS" on Lada Vesta

The fuel pump on the Lada Granta does not work. How to replace the fuel filter on a Lada Kalina with your own hands. installing a new fuel pump strainer

To control all functions of cruise control and jetter, a four-button radio key fob (included in delivery) is used.

Description of Cruise Control on Vesta

The Cruise Control system on the Lada Vesta in the modern world of cars is an integral part of comfort and safety

The presence of such a system in a car allows you to reduce fatigue when traveling long distances, and also helps reduce fuel consumption, which is very important in modern conditions.

Most foreign-made cars have been equipped with such a gadget for a long time. Domestic cars, unlike foreign cars, until now were not equipped with the Cruise device. This made them less attractive to the car enthusiast who cares about such qualities as safety and comfort.

On a Vesta car, Cruise Control allows you to activate, set and change the speed in cruise mode while driving, switch jetter operating modes (“Economy”, “Dynamic”, “Sport”) and program jetter operation for the Lada Vesta Mechanica cruise control option, in other words, for a car equipped with a manual transmission.

It is advisable to use the operating modes of the Jetter e-gas corrector as follows: “Economy” mode when parking and driving in reverse, as well as in traffic jams and in case of heavy ice. This mode is also suitable for less experienced drivers. Dynamic mode for active driving in the city. And finally, the “Sport” mode is on the track.

This device appeared on the automotive electronics market under the name JET-CRUISE VS and is intended only for cars of the Lada Vesta family.

This device allows you to maintain a constant vehicle speed set by the driver in the range from 40 to 150 km/h. We offer you to buy cruise control in our online store and improve your car at minimal cost. If you have long wanted to find cruise control for your car, then your search can be considered over.

This is becoming especially important now that stationary speed measurement systems are increasingly being installed on roads.

This function works as follows: when the cruise control is turned off, the maximum permitted speed on a given section of the road is set, and if you exceed the set speed, JET-CRUISE signals this.

The JET-CRUISE kit includes Jetter. It is installed on cars with an electronic gas pedal “E-gas” and eliminates the delay in opening the throttle valve when pressing the gas pedal.

Cruise control on E-gas is a good way to increase the level of safety of your driving.

Installation of the JET-CRUISE VS cruise control system takes no more than 20 minutes.

Vesta cruise control can be purchased in our store.

Cruise control and speed limiter on Lada Vesta cars

In some modifications of the comfort and luxury trim levels in Lada Vesta cars, you can encounter such an interesting function as cruise control and a speed limiter; these functions greatly simplify driving the car, and make the ride pleasant and comfortable. The speed limiter and cruise control control buttons are located on the left side of the car’s steering wheel, the leftmost “+” and “-” buttons set the required speed, both on the cruise control and the limiter, the rightmost buttons directly activate these functions (the top one is cruise control , lower - speed limiter).

The speed limiter allows the driver to choose the speed that he would not like to exceed while driving the car, after installing the limiter, for example, at 60 km/h, no matter how hard the driver presses the accelerator pedal, the car will not exceed the set limit until the limiter will not be disabled. This function is convenient for city driving, where a certain speed limit is set, and violation of it is punishable by a fine.

In order to activate the speed limiter, you need to press the lower right button (on the left side of the steering wheel), after pressing it, the orange speed limiter indicator on the instrument panel will light up, using the “+” and “-” buttons set the required speed, after which the indicator will change color to green, which in turn will mean that the limiter is active. To disable the function, press the lower right button again. The minimum permissible speed for the limiter to operate is 30 km/h.

Cruise control works a little differently than the speed limiter, but it still limits speed. With the help of cruise control, the driver can set the speed he needs, and the car will then maintain it independently without the participation of the driver’s feet.

In order to activate cruise control on the Lada Vesta, you need to press the upper right button (on the left side of the steering wheel), after which the orange cruise control indicator on the dashboard will light up (see photo above), after which you can proceed to setting the required speed using the " +" and "-", adjusting the speed, the cruise control indicator will change color to green. The set speed is displayed on the on-board computer display and will be maintained until the driver takes control of the car. If the driver presses the brake or accelerator pedal while cruise control is operating, the indicator will turn orange again; cruise control can be restored by pressing the “Res” key. The minimum permissible speed for cruise control to work is 40 km/h. Cruise control will be useful on country roads during long journeys.

source

What is cruise control

The engineering idea is more than 70 years old. To take care of driver fatigue during long drives in suburban areas, manufacturers began to introduce a mechanism into the car design that automatically regulates the speed mode. There is no need to press the accelerator: the driver gets less tired. In this case, the device takes into account descents/ascents and wind.

Cruise control capabilities. Photo source: https://1gai.ru/publ/523156-polzovatsja-kruiz-kontrolem-v-dozhd-opasno-ili-vse-zhe-mozhno.html

The system is activated at a speed of at least 40 km/h and is supported up to 180-200 km/h, so the option is not relevant in the city. The function is standardly installed on foreign cars and some versions of domestic auto industry products. But the mechanism can be mounted on any car. The type of engine, transmission (manual transmission, automatic transmission, robotic gearbox or variator) do not matter for installation, however, neither does the body: sedan, station wagon, hatchback.

Cruise control DRIVENGE Lada Largus

Cruise control DRIVENGE Lada Largus Mechanica (since 2014)

Cruise control is equipped with a full-fledged steering column switch!!! Drivenge cruise control Lada Largus MT has a 3-year warranty.

All DRIVENGE cruise control models are Certified.

Place an order on the website and receive FREE DELIVERY within the Russian Federation + GIFT!

Cruise control significantly increases the level of comfort in the car; every driver can remember more than one situation when, from constantly pressing the pedal, the leg became numb, and from constantly changing the position, the back and neck began to hurt.

One factor in installing cruise control is efficiency. By controlling the gas pedal yourself, the car is much more likely to be in the acceleration-rolling mode, which can increase fuel consumption by up to 10-15%.

Another advantage of this cruise control is the presence of a pedal booster function. This software function allows you to set one of three preset modes.

Economy mode - weak response to the gas pedal, maximum fuel economy.

Drive mode is identical to the factory mode, perhaps a little more economical.

“Sport” mode - the fastest possible response to the gas pedal, with slightly increased fuel consumption, the car becomes much faster.

Control of the device is similar to standard cruises. Switching on is done using one button, switching off with the brake pedal or by pressing the button again.

Cruise control model Drivenge Lada Largus MT was created specifically for this model with a manual transmission.

It doesn’t matter what kind of ECU and gas pedal connector the Lada Largus has. For each unit, the device is equipped in such a way that intervention in the electronics and software of the vehicle control units is not required

Detailed instructions are included with the device.

You can install the device yourself without having serious knowledge of electronics.

Video review of the DRIVENGE cruise control installation.

Functionality:

• Activates cruise control at the current or last set speed.
• Automatically maintains the set speed in cruise control mode.
• Change the set speed using the buttons in 1 km/h increments or using the gas pedal.
• Restores the last set speed.
• Automatically deactivates cruise control when the brake or clutch pedal is pressed.
• Enabling or disabling pedal boost mode.
• Select one of three modes of operation of the booster pedal.
• Maintaining increased (set) idle speed.
• Connect to a computer to update internal firmware.
• Saving all parameters of the last used values ​​(speed, modes, etc.) in non-volatile memory.
• Resumes, after turning on the power, the operating mode in which the power was turned off.

Equipment:

• Cruise control main control unit
• Under the steering wheel controller for cruise and booster control
• Wiring harness for connecting to vehicle wiring
• LED in holder with wire + connector housing
• Clips for connecting to car wiring without breaking the wires
• Plastic clamps for fastening wires
• Fabric insulating tape for wrapping harnesses and wires
• Operating manual with warranty card

Buying cruise control is easy, fill out the order form or place an order by phone,

Lada Largus Cross – a budget multi-purpose station wagon

When the booster pedal and cruise control are inactive, DRIVENGE completely excludes itself from the car’s circuits. So even if for some unforeseen reason DRIVENGE fails or “loses” power, the car will operate normally.

DRIVENGE Features:

• Low price
• Easy installation
• Does not require intervention in the on-board computer settings
• High accuracy of maintaining the set speed
• Integrated switchable booster pedal with three operating modes
• Turning on cruise at the current or previously memorized speed
• Adjustment of the set speed in steps of 1 km/h
• Support of specified idle speed
• Possibility of firmware update

Supported car models: Volkswagen Polo Sedan KIA New Rio (QB) 2011+, Kia Cerato II (2009-2013), Kia Ceed I (2009-2012) Hyundai Solaris, Grand Starex, Starex H1 Renault Duster Nissan Terrano, Nissan Almera III (2013- ) Lada family UAZ cars Fiat Albea Datsun on-do * - free delivery by Russian Post is valid subject to advance payment of the order (not cash on delivery) and the order amount is at least 5,000 rubles

Selecting cruise control

As you know, this option is offered by the manufacturer in the “luxury” configuration of not only Grants, but also Kalinas, equipped with an automatic rifle.

However, more modest modifications (for example, “norm”) are not equipped with cruise control. But still, nothing prevents you from installing this device yourself. The easiest way is to mount a standard device.

This opportunity is available to the owners of the Grant (liftback or sedan) and the second Kalina, equipped with both manual transmission and AMT.

If an automatic transmission is installed, then the standard option will not work - you will have to use universal cruise control from other manufacturers.

It is important that the car also has a TsBKE. It is better to install a standard device equipped with 2 displays

It is important to clarify when purchasing which gearbox you have on the Grant. Each case requires a different cruise control

It is better to install a standard device equipped with 2 displays

It is important to clarify when purchasing which gearbox you have on the Grant. Each case requires a different cruise control

You will also need a steering column switch mounted on the right. In principle, the left one is also suitable - it will allow you to preserve the native design style. You will also need a new instrument panel with openings for the previously mentioned displays. After this element and switch are installed, it is necessary to reconfigure the ignition key and possibly change the ECU firmware.

Needed or not

You can buy a multifunction steering wheel and install it on your Lada Vesta yourself. This will make your car much more comfortable and convenient. You don't have to reach for the stereo to change the song or adjust the cruise control. The difficult part in installing the multifunction steering wheel is strict adherence to the wiring diagram.

If your Vesta is not “Lux”, but a regular package, and there are no gray wires in it, then the likelihood of mixing up the connection is greater. Therefore, be more careful when connecting the Vesta multifunction steering wheel.

Many Lada Vesta car owners will be interested in this option. Cruise control allows the vehicle to move, including descents and ascents, without the driver pressing the pedal. A person just needs to set the electronic system to a certain speed. This option is well suited for relatively empty tracks and roads. Lada Vesta with cruise control allows you to significantly save human resources on long journeys.

Owners can boast of this advantage only when purchasing the Lada Vesta Luxe and Comfort configuration (with the Multimedia option package). Luxury cars are equipped with a base platform on which steering wheel buttons are installed. For Classic it is possible to mount a multi-function steering wheel.

Required

Need to buy:

• multifunction steering wheel (catalog number: 8450006832);
• steering column switch (volatile) with wires for the steering wheel buttons (catalog numbers: 8450006923, 8450006924), or buy a cable with a large number of tracks and replace it inside the volute;
• BLS pins for cochlea connector.

To control the radio:

• cable of 5 wires with a diameter of 0.5 mm;
• blue mini-ISO connector C3 (for Classic or Comfort configuration);

To operate cruise control and speed limiter:

• cable of 3 wires;
• connector for connecting wires (radio and cruise control controls) to the snail block.

How to use the system?

On the Lada X Ray, cruise control is activated in the same way as on other VAZ models. The control unit is located on the steering wheel. The buttons are located on the left side. The system can be turned on when the speed is above 40 km/h. An emergency function is provided: autospeed is turned off if the brake pedal is pressed.

The buttons perform the following functions:

• 1, 4 - regulate speed;
• 2 — temporarily disables the system or enables restrictions;
• 3 — turns on and off autodrive mode;
• 5 — return to the last set speed value;
• 6 - controls the speed limiter.

The Lada Largus device is turned on by performing the following sequence of actions:

1. Switching on is done by pressing button 3. After this, you need to remove your foot from the gas pedal.
2. Using the “-” and “+” buttons, we set the desired speed, which is displayed on the monitor under the speedometer. Each press of the button changes the speed by 1 km/h, increasing or decreasing it.
3. You can use the brake pedal to brake if necessary. In this case, the system will automatically turn off.
4. You can return the previous settings by pressing the Res button (5). The car gradually accelerates after turning on the cruise control. If you need to accelerate quickly, you need to switch to manual mode.
5. To turn off autospeed, press button 3.

The system has a pneumatic actuator that controls the throttle valve, so there is no need to step on the gas. A special cable is connected to the throttle valve. When cruise control is activated, it controls the fuel supply by replacing the accelerator pedal. The unit, thanks to information from sensors, maintains the set speed.

Knowing how to operate the system, you can make any train, even the longest one, comfortable.

How to install standard cruise control on a Lada XRAY with a Renault-Nissan internal combustion engine

Currently, the Lada XRAY multifunction steering wheel only allows you to control the radio. And the left block of buttons, responsible for cruise control and speed limiter, is missing. AvtoVAZ promises to equip its crossover with this option in 2021, but for now you have to install cruise control yourself.

Depending on the engine (VAZ or Renault-Nissan), various engine control units (ECUs) are installed in the Lada XRAY engine compartment.

In this regard, the installation and connection of standard cruise control on a crossover varies. Next, let's look at the instructions for a 110-horsepower French engine (Renault-Nissan H4Mk).

For the VAZ engine, instructions are here.

For TOP and TOP Prestige trim levels you will need:

• Multifunction steering wheel Lada Vesta with cruise control buttons, article number 8450006832. Approximate price from 3500 to 8500 rubles.
• Button for turning on cruise control and speed limiter, article number - 255500002R. Cost from 1200 rubles.
• ELM327 adapter for activating the function in the ECU and instrument panel. About 1000 rubles.

For simpler versions of the car you will additionally have to buy:

• Steering column switch module (popularly “snail”), article number 8450020003. Prices from 6,000 rubles.
• Wires that will have to be pulled from the passenger compartment to the engine compartment.

Articles about Lada X Ray

INSTALLATION AND CONNECTION

Remove the plug between the headlight range control and mirror adjustment. Behind it there is a connector with wires, which we connect to the button (255500002R). Install a button instead of a plug.

We replace the Lada XRAY steering wheel with a steering wheel from Lada Vesta (8450006832), but leave the right block of buttons from the crossover (from Vesta it will not work). The main reason for replacing the steering wheel is the presence of wiring inside it.

To do this, we disassemble it by prying the white retainer with a flat screwdriver. +12V can be taken from the steering angle sensor (pin No. 8), which is located under the steering wheel. It can also be borrowed from the plug connector of the cruise control button between the “mirror control” and the “headlight range control” (contact No. 1)

Articles about Lada X Ray Cross

In simpler configurations, the steering column switch (snail) may not have the necessary wires. We change it to another one (8450020003). You will also need to stretch 4 wires to the block with the ECU wires (from the passenger compartment to the engine compartment through the hole with the cable for opening the hood):

• Two wires to 3 and 4 contacts of the button (255500002R). If the speed limiter turns on instead of cruise control, simply swap the wires.
• Two wires up to 2 and 8 pins of the snail connector. The connection order is not important here.

As a result, the cruise control and speed limiter will be activated from a button on the panel (these buttons on the steering wheel will be inactive, since they are not fixed!), and the functions will be controlled by buttons on the steering wheel. To have all the controls only on the steering wheel, you need to use a fixed button emulator (read below).

ACTIVATING A FUNCTION IN THE ECU AND INSTRUMENT PANEL

You need an “ELM 327” adapter and a laptop with the software installed:

• drivers for ELM (we register the COM port)
• Python
• Pyren and CLIP base

We connect the ELM 327 to the OBD-II connector of the Lada XRAY. Then:

1. Run pyren.bat (make sure that the COM port of your adapter is specified in the file)
2. Scroll (using the N button) the list down until we see “logan 2/ sandero 2”, press the numbers against this inscription and enter.
3. Select the block -> INSTRUMENT PANEL (P/PAN), -> Changing Configuration -> ADJUST/LIMIT. SPEED —> yes —> 2—> yes.
4. The instrument cluster will reboot.

1. Select the block -> INJECTION SYSTEM -> Configurations scenarios -> PROGRAMMERS. SPEED LIMITS—>yes.
2. Exit the script and disconnect the adapter from the car.

Connecting the buttons on the steering wheel to the radio

We supplement the block with the cruise control wires with wires for controlling the radio and insert it into the cochlea. We pull the wires to the radio and connect them to the blue mini-ISO connector. Everything according to the scheme:

If you are using a non-standard Vesta radio, then you will have to make an adapter for a specific model of audio system.

As a result, using the buttons on Vesta’s steering wheel, it will be possible to control the radio, cruise control and speed limiter, and the button backlight will also work. The only difference from the standard implementation is that there will be no indication of cruise control operation on the instrument cluster. To do this, you need to flash it or activate it via ELM327. By the way, during the panel test, pay attention to the cruise control indicators (icons in the speedometer well at about 140 and 160 km/h); if they are on, then the firmware is correct.

Here is the cruise control indication on Vesta, which has a multifunction steering wheel from the factory:

Let us remind you that the “Multimedia” option package includes not only a multifunction steering wheel, but also a rear view camera. We looked at how to connect a camera to a multimedia system earlier. By the way, another way to modify Vesta is to install fog lights.

Photo: logbook vlad21074

Keywords: Lada Vesta steering wheel | cassette player Lada Vesta

+15

Share on social networks:

Found an error? Select it and press Ctrl+Enter..

Purpose of the system

The cruise control function ensures comfortable driving while maintaining a set speed. Thanks to it, it is much easier for the driver to cover long distances, especially on country roads. Foreign manufacturers began equipping their cars with similar systems back in the early 70s, and the domestic auto industry only recently “awaited” the appearance of this technical miracle. On the Lada Vesta, cruise control is installed in the luxury and comfort trim levels, both with an automatic transmission and a manual one. Let's talk about how to use this smart device, unusual for domestic car enthusiasts.

What does having cruise control in a car do for a driver?

This is a very useful thing, especially for long trips, it allows you to ride comfortably without straining your legs or worrying about exceeding the speed limit. If the car has a manual transmission, you do not need to change gears; it remains the same both on descents and on ascents. The function is also useful for beginners who do not yet know how to adjust the safe force of pressing the gas pedal.

At the bottom on the right side of the option control is the speed limiter button.

The principle of the limiter is similar to cruise control, but there are differences. To turn on the speed limiter, you also need to click on the sign, the orange indicator will light up, use the plus or minus keys to select the desired speed, the value will be shown on the speedometer, after installation the green light will turn on. When the limiter is operating, the speed limit will not change, even when the accelerator pedal is pressed. This is very convenient, for example, when driving around the city, where fines are imposed for exceeding the limit.

• https://xn--80aal0a.xn--80asehdb/do-my-self/tuning/tuning-lada-vesta/5633-kak-aktivirovat-indikaciju-kruiz-kontrolja-na-lada-vesta.html
• https://vesta5.ru/kak-polzovatsyakak-rabotaet-kruiz-kontrol/
• https://vestaz.ru/kruiz-kontrol-lada-vesta-kak-etim-polzovatsya/

Benefits of Cruise Control

Having cruise control in your car allows you to:

• Maintain a constant speed regardless of the nature of the route;
• Don't worry about speeding;
• Do not constantly keep your foot on the gas pedal;
• Does without gear shifting (on manual)

This is very convenient, especially when traveling along a lightly congested highway. By turning on this function, the driver can move calmly and relaxed by simply setting the desired speed and taking his foot off the gas pedal. The brakes work as usual, and in case of emergency the car can suddenly reduce speed.

How does cruise control work on Lada Vesta and how to turn it on?

A correctly configured device ensures strict adherence to the selected speed without exceeding and regardless of the weight load the vehicle is experiencing. The system perfectly regulates the position of the throttle valve (limiter), based on the readings of the corresponding indicators. The faster the information reaches the cruise control computer system, the more stable and safe it operates.

On the right side of the Lada Vesta steering wheel there is a multimedia system, and on the opposite side there is a cruise control unit, which contains the following buttons:

• turning on and off the operation of the entire system;
• correcting and regulating speed limits;
• disabling both functions for a while.

There are also buttons here that allow you to return to the last saved presets.

You need to understand that the device accelerates the car rather slowly; if this does not suit you, switch to manual control mode.

Conclusions. Is it worth installing cruise control?

The appearance of such a function as cruise control in the Russian Lada Vesta car evokes positive emotions among buyers. It makes driving more comfortable and safe, and also allows you to save fuel during long trips.

It is advisable to use this function during long journeys, when the route is relatively clear. In city mode, cruise control is clearly inconvenient and irrelevant. Based on this, we can conclude that those drivers who often travel long distances and want to feel more relaxed during a tiring trip should install this function on their car.

How to connect the multifunction steering wheel on Vesta “Lux”

Connecting the multifunction steering wheel in the luxury version of Vesta is more convenient. This configuration is distinguished by the presence of gray wires in the existing wiring harnesses.

The multifunction steering wheel snail is connected in the following order:

There are special holes on the sides of the steering wheel. Insert the rods into them and press. In this case, the airbag unit should rise

Pull it out, being careful not to damage the elements of the block. Disconnect all wires and remove the steering wheel. To do this, unscrew the central bolt and pull the steering wheel towards you

When pulling out the steering wheel, make sure that the wires pass through the hub hole and are not damaged. Installation of the multifunction steering wheel is carried out in the reverse order of operations.

Features of operation

Those who have driven cars equipped with standard cruisers will most likely not be attracted to such products - they are not very convenient to use and look unrespectable. But if such toys are new to someone, they may well come in handy.

Isn’t it dangerous to drive with these devices if they suddenly fail? After all, we interfered with the standard electrical equipment, breaking some of the car’s control circuits... We checked that when the power from both systems is turned off, the ability to control the car remains. Therefore, the manufacturers of both devices did not violate the old principle of “do no harm.”

Drivenge.

I constantly want to press the new steering column “lever”, which also “breathes” along with the steering column casing.

Jet-cruise KH.

The remote control is not backlit - on a dark country road you will have to manipulate it by touch. The indication only works at the moment of operation.