Removing mirrors
- Pry off the cap of the mirror control knob and unscrew the fastening screw with a Phillips screwdriver.
- Remove the triangular-shaped plug by prying it up with a flat-head screwdriver and unlatching the latches.
- Unscrew the three mirror mounting screws using a Phillips screwdriver.
- Remove the mirror from the car.
Disassembling side mirrors
Removing the mirror
First we dismantle.
Naturally, it will be more convenient to disassemble the mirror removed from the car, so it should be removed. What is needed for this?
Removing a power mirror. First, you need to remove the mirror adjuster locking bracket, unscrew the three screws that secure the mirror to the door frame, and then remove the mirror itself.
Removing the electric mirror. The first thing to do is disconnect the negative terminal from the battery. Next, you need to disconnect the block from the electric drive wires, unscrew the three screws securing the mirror to the door and remove it.
Replacing the mirror element.
Lifehack What is this for? SE Priora mirrors have arrived for the VAZ. Dismantling the entire mirror element of the VAZ Lada 21 Nov 0 Comments.
Installation of mirrors from Priora on VAZ. Which side mirrors would I choose for VAZ? lada 18 Dec 0 Comments.
VIDEO: replacing the mirror element on a VAZ 2111 2112 2110
More on the topic. How much does it cost to repair thresholds on a VAZ? Before repairing the removable thresholds of a car, you need to remove them. How to add oil to a VAZ engine. As you can see, the replacement process is very simple and does not require special equipment. How to carefully remove the trim on a VAZ. These nozzles are ball-shaped, and their driver can adjust The corrector on a VAZ does not work In order for the hydrocorrector of VAZ headlights to work again, the device must be repaired VAZ replacing wiper blades Replacing frameless wiper blades is a procedure that needs to be performed How to check the armored ducts of a VAZ 16 valves Now you know how to check the armored ducts without a tester.
But there is How to check the integrity of the cylinder head gasket of a VAZ If you are sure that part of the antifreeze goes into the engine through Repair of the internal combustion engine of Lada Kalina 16 valves Motorists cite facts when, in addition to the valves, pistons were damaged, connecting rods were bent, How to replace the windshield wiper motor on a VAZ Remove the windshield wiper mechanism on car VAZ and VAZ gasoline pump replacement Video material will tell you how to replace the gasoline pump, as well as VAZ repair instructions. You can familiarize yourself with the design of its systems, components and electrical equipment. Replacing the engine of the VAZ fuel pump injector Like most injection cars, the VAZ has a gasoline pump How to change the door limiter on a VAZ Door limiters are special devices that allow you to open and close doors silently, the speed of the VAZ does not drop. The fact is that when much more air enters the carburetor than gasoline, the mixture How to correctly pick up the tachometer of a VAZ Here you can Read more about the principle of operation of the tachometer.
How to run wires for the speakers of a VAZ Only this speaker is capable of providing natural transmission of low-frequency sounds, because the other components of the acoustic system do not turn on the starter relay on a VAZ. You need to remember how the wiring diagram for the starter on a VAZ works. There are only two on a VR. How to lubricate the steering wheel of a VAZ so that the steering wheel turns well and with little effort, for this purpose the steering column is constantly lubricated New articles Replacing rubber springs on gas Replacing rings on a gazelle engine.
How to open the hood of a gas radio Lifan Solano, what kind of flash drives. Replacement of Toyota Camry fuel pump mesh. Where is the Lifan Solano cigarette lighter fuse?
Removing and installing the internal rear view mirror on the VAZ 2110, 2111, 2112
An article with photos and videos for everyone who wants to replace the interior rear view mirror on VAZ 2110, 2111, 2112 cars.
1.Remove the decorative cover using a Screwdriver...
2. ... to remove the fastening pistons from the holes in the bracket.
3. Now all that remains is to unscrew the two screws securing the mirror to the bracket and remove it. Reinstall the mirror in reverse order
How to disassemble the rear view mirror of a VAZ 2110
It often happens that the rear view mirror mount becomes loose and the mirror holds well; in other words, she disappears (someone dropped her off at your place). It happens that the side mirror is broken or cracked - you need to change it. The mirror angle adjustment drive needs to be repaired.
Of course, go to the dealership and the mirror will be attached in place. If there is no service nearby, you will have to act on your own. The rear view mirror is important on the road: the driver can observe the situation on the road in the field of view behind the rear fenders and rear bumper. The mirrors of different brands of cars are different: interior mirror and side mirrors, regular, folding, electric, etc. When removing and disassembling any mirror, you must be very careful not to damage the mirror itself.
In order to disassemble the mirror, you need the following tool:
3.2 flathead screwdrivers (they clamp the latches with them).
A narrow, long screwdriver and a piece of soft cloth (to wrap the screwdriver).
10 star or regular screwdriver with variable bits.
How to remove the electric side mirror (Included):
1. Remove the triangular trim from the front door.
3.5. Disconnect the mirror wiring connector. Do not damage the heating mirror wiring!
3. While holding the mirror, unscrew the 3 mounting screws.
4. Remove the mirror assembly.
5. The completed mirrors are made in reverse order.
Do it yourself, repair Lada Kalina mirrors, do it yourself. Removing the mirror element
Removing the rear view mirror using a mechanical drive:
1. Remove the mirror retaining bracket.
3. We remove the mirror.
4. Installation is in the reverse order.
Price issue
First of all, we will orient you a little on the price tags that are presented on the market today.
The cost may vary depending on the manufacturer, technical features of the product and the region of its sales. Therefore, prices are average.
Mirror type
approximate cost
Outdoor heated
Obviously, the characteristics of the panoramic interior mirror provide a better view, and the presence of heated exterior mirrors provides comfort and does not require constant wiping. It is better to pay more, but buy new functional products.
How to remove a side rear view mirror with your own hands
This accessory is not as simple as it seems. Most often, various devices are built into it. For example: turn signals, LEDs, heating parts. For this reason, before removing the mirror, it is necessary to remove the negative charge from the battery. This is necessary in order to minimize the likelihood of a short circuit occurring during work.
replacing the side rear view mirror
The tools needed for this repair can be found in every garage. These include: a set of screwdrivers of different sizes, a household hair dryer, a plastic spatula, electrical tape, a small piece of soft cloth, and a wrench. In addition, attention to detail, caution and a desire to do everything right will come in handy.
Removal process. After the negative charge has been removed from the car battery. You can start dismantling. To do this, you need to open the car door and remove the handle for changing the mirror angle.
The process for removing the angle knob varies on individual vehicle models. For example, on some it is enough to pull the handle towards you for it to come out of the grooves. On other models, you will have to unscrew it counterclockwise or, before removing it, you will need to unscrew the bolts that hold it in place.
In order to remove the mirror, you need to find the bolts that hold it in place. As a rule, they are located under a decorative lining and are located so that they are not visible. The decorative hiding element must be removed. Often the rubber gasket is removed together with it. It is important not to lose it due to the fact that these items are not sold separately in stores, with some exceptions. When the cover plate is removed, the bolts are clearly visible. They need to be unscrewed; in addition, to avoid confusion during assembly, it is best to photograph the location of the multi-colored wires.
How to disassemble a side mirror
First you need to decide on the make of the car and its design of the mirror. Then inspect the visible damage and read the repair instructions. In approximately half of the cases, side mirror malfunctions consist of a broken housing and broken glass. Although different cars will require a different approach to replacing a mirror, one thing is similar for them. If the mirror is cracked, you need to pull out the burdock with the mirror from the holding hinged bracket, which ensures mobility, and then replace it with a new one. The main thing during installation is not to overdo it! The mirror is very fragile, so it is better to perform the procedure at positive temperatures; in winter in a heated garage or in a service station.
How to remove the side mirror of a Lada Granta
Side rear view mirrors are an integral element of the design of any vehicle. They allow better control of the road situation, promote traffic safety, and optimize the aerodynamics of the body.
Some mirrors are additionally equipped with direction indicators (read the instructions for how to replace them), this statement also applies to the popular domestic car Lada Granta. The need to remove mirrors may be due to the following factors:
- Mechanical impact that caused the destruction of the housing.
- A crack or other defect on the mirror element. (Instructions for replacing the mirror element)
- Burnt spiral of heated mirrors or other damage to the electrical part.
In general, the operation of removing a mirror does not present any particular difficulties; it can be done on your own with minimal waste of time, so there is no need to turn to professionals.
Removing the outer and inner rear view mirrors
Rear view mirrors are an integral part of the car. Even those drivers who have equipped their “swallow” with a monitor or camera cannot do without mirrors. Therefore, keeping them in good condition is the primary task of every car owner. Before moving on to the procedure for dismantling the mirrors, we will list the tools that we will need for the job.
Tools required for dismantling
- Phillips screwdriver;
- flat blade screwdriver.
How to disassemble an external mirror
It is advisable to dismantle the exterior mirrors in a certain sequence.
- Using a screwdriver, remove the locking bracket to which the mirror angle adjuster is attached.
How to properly remove the interior mirror
Changing the rear view mirror in the cabin is a little more difficult. Work must be carried out in the following sequence:
- The plastic plugs above the interior mirror mounting screws are carefully pryed off with a flat screwdriver and removed.
- The mounting screws are unscrewed with a Phillips screwdriver.
How to remove a mirror from a windshield
Dismantling a glued mirror does not require any special skills. Proceed as follows:
- In some modern cars, the bracket with the interior rear view mirror is glued directly to the windshield. To remove it, you must remove all plastic plugs from the bracket (if any).
- After this, the mirror is turned counterclockwise with both hands and removed from the socket.
How to change a mirror on a VAZ 2110
The mirror element is an integral part of the rear view mirror on the VAZ 2110 vehicle. Naturally, there are many modernized mirror designs, but regardless of innovation, a specialized mirror element plays a key role. It is this that provides high-quality display from a certain angle, which allows the driver to see all the necessary obstacles while driving. The creators repeatedly produce these components in the form of a separate spare part, which, if necessary, can be removed and replaced or repaired.
Types of mirror elements and their structure
It is important to note that competent service center professionals claim that it is quite difficult to carry out the procedure associated with replacing mirror parts on the rear view mirror of a VAZ-2110. This is due to the fact that the part has a rather fragile structure and can be damaged. Situations often occur when, during the process of replacing the mirror housing, the element itself is damaged.
This leads to various negative consequences. Before you independently replace such a mirror part, you need to understand exactly that the unit consists of four main components:
- Mirror element;
- Frame;
- Mechanism for setting the deflection angle;
- Bracket.
How to disassemble the side view mirror on a VAZ 2110
It often happens that the side view mirror becomes unusable for one reason or another. Most often it’s a pebble, of course, but that’s not the point. In this article we will explain step by step how to disassemble the side view mirror on a VAZ 2110.
Guide on how to disassemble a side view mirror
First, remove the side view mirrors.
After this, unscrew the mirror adjustment lever.
After this, hold the mirror towards yourself and a pin should appear. The plate with the pin will not be particularly visible, so be careful.
Using a file or screwdriver, press out the pin.
Remove the mirror from the collet. You will need a thin screwdriver.
You should ask a friend to hold the mirror body, and you should pull the mirror itself, simultaneously bending all the clips from the collet, and the mirror should pop out.
To prevent the mirror from dangling, you need to wrap the holders with film, this should help solve this problem.
Reassemble everything in reverse order.
You can watch the video on how to disassemble the side view mirror on a VAZ 2110:
We remove the rear view mirrors on a Chevrolet Niva ourselves
Removing the mirror from either the left or right side is quite simple . To do this, you need a set of screwdrivers, pliers and half an hour of time.
The mirror could be removed faster, but due to the special location of the contact blocks for the adjustment and heating drive, you will have to disassemble almost the entire door trim.
Let's be patient and get started.
- We unscrew all the screws that secure the door card (door trim).
Disconnect the connectors of the two exterior mirror wiring harnesses.
After this, if necessary, you can replace the mirror element, the adjustment drive, or repair the broken bracket.
Disassembling the side mirror elements
The mirror is disassembled by dismantling the mirror element . To do this, use a thin screwdriver to unclip all 12 latches that hold the mirror element to the servo drive. They can be accessed through a hole in the plastic case, but you should never rush, since overdoing it can break the mirror surface.
vote
Article rating
