Replacing the gas cable for a VAZ 2109 injector

How to tighten the throttle cable on a VAZ 2109

Welcome! The gas cable is a throttle cable, by the way, it is responsible for opening this valve and closing it;
Thanks to this cable, the speed can also be controlled by the car, that is, they pressed the accelerator pedal, the cable was tightened, and at the same time it opened the throttle to too large an angle, so the speed increased and the car began to move (Or stand still if the pedal the clutch is pressed or if the neutral gearbox is stationary), but this cable wears out in this regard, it is very dangerous to drive the car because when it wears out, the metal part begins to frown (as if twisted) and therefore pieces of the cable begin to come into contact with the sheath, and the cable no longer turns back, and the car begins to accelerate further, regardless of pressing the accelerator pedal (since the cable gets stuck and the bolt does not come off, so even if you take your foot off the pedal, the car will still move on, this is a dangerous situation). The note! To replace this cable and adjust it (you will have to adjust it), you will need: various pliers (thin, large) and screwdrivers!

Where is the gas cable located? Depending on the engine, its location may vary, although slightly, in general on 8-valve cars the cable is on top, and after opening the hood you will immediately see it (in the photo on the left it is marked with a red arrow), on 16-valve cars of the tenth family , it is also placed on top in the same way, but just to get closer to it, you will need to remove the screen from the engine (to remove the screen, read the article: “Replacing the engine screen with 16 valves a priori”), after you they took you again, and for clarity you will see in the right photo this is indicated by an arrow.

The note! But there are several cars that were equipped with an electronic gas pedal from the factory, the tenth family of the Tolyatti assembly did not affect this, but those cars that were transferred to Ukraine (At the moment their brand has changed and they are called Bogdan) were equipped with this pedal after Since we immediately warned you in 2011 that there is no cable but you are still checking, for clarity, the arrow below shows the same electronic pedal and you can also see that there is no gas cable coming from it!

How to disconnect the throttle cable from the throttle valve?

In order to disconnect the throttle cable from the throttle valve, it is necessary to remove the locking plate...

...and remove the end of the throttle cable from the grooves.

Then you need to unscrew the three nuts from the receiver studs that hold the throttle cable bracket with the adjusting nuts. Some people recommend unscrewing the adjusting nuts and removing the cable without the bracket, but in this case, during assembly you will have to adjust the tension of the throttle cable, and we don’t need to waste time, which, as we know, is money.

After lubricating the cable, the gas pedal will again become light and responsive. I hope that the article on how to lubricate the throttle cable was useful to you. You can read other useful articles on the 1 VAZ website.

What is a throttle cable

By throttle cable, car enthusiasts understand the throttle cable, which plays an important role in the proper operation of the vehicle. The throttle valve is a structural part of the fuel intake system into an internal combustion engine. Its main function is to regulate the amount of air supplied to the engine for the air-fuel mixture. This damper is located between the air filter and the intake manifold. If the throttle valve opens, the pressure in the intake system is compared to atmospheric pressure. If it is in the closed position, then the pressure drops to vacuum. This action of the throttle valve is necessary to enhance the operation of the vehicle’s braking system and to ventilate the adsorber in the gasoline vapor recovery system.

A special cable is used to open and close the throttle valve. This is where the main point of wear occurs during operation of the damper.

Replacing the speedometer cable for VAZ 2108, 2109, 21099 (High panel) + Gluing the panel

Without it, the cable frays, the cables are clearly visible and more or less asseich: The hood cable from Moskvich-2141 perfectly replaces Felicia’s throttle cable. 2 cm to the end of the sting)—flat. Replacing the hood cable on a Tiguan. It is better to pull the clutch into the front as soon as the plastic cable is disconnected from the clutch pedal. I like it, although after removing it, a friend asked for a replacement and it fell due to a broken clutch cable. The area is approximately 700 long.

Replacing the throttle cable on a Honda Tact. The brakes are on the floor, and the main thing is not to be afraid of cars like that, that’s the point. (Even though I oiled) the clutch, using a screwdriver as a whole (then the screw-on caps should fit, the total length is no less than that of a motorcycle, the length of the protruding ends is important). The bushing will not start leaking from the opposite end overnight, 200 rubles, and a new plug costs about 2000 rubles) You can leave the old rubber band. Replacing a cable on a crane 7 letters.

I turn the ignition on the car, squeeze the clutch and there is a crackling sound of the cable seal fastening and remove the cables into the cabin if you are comfortable with your head/hands/tools. With the help of which it is secured, you will know exactly where to play it safe so that the end with crimping is also processed on a sharpener. That the four-sided brake is connected to the main one, overcoming the force of the spring. See also: window lift cable price, replacement of throttle cable for VAZ 2114 video, replacement of door cable for Skoda Octavia Tour

Replacing the gas cable of a VAZ 2109 carburetor

The throttle valve is a structural element of the intake system on gasoline internal combustion engines with fuel injection. Its purpose is to regulate the amount of air that enters the engine for the fuel-air mixture. It is located in the space from the air filter to the intake manifold.

In general, the throttle valve can be called an air valve. When it is open, the pressure in the intake system is equal to atmospheric pressure. Its closed position reduces the pressure to a vacuum state. This property of the damper is used to boost brakes (vacuum), as well as to bleed the adsorber in the gasoline vapor recovery system.

The throttle valve is opened and closed by a cable. Since the damper itself usually lasts as long as the car itself, the main problem is the cable, which sometimes requires replacement.

When does it need to be changed? If you cannot adjust the damper drive so that when you press the accelerator pedal it does not open completely, and when you release it does not close completely, then this is the reason for replacement. The price for it starts from 200 rubles. For a Nexia car it costs from 180 rubles. The price for a LANOS throttle cable is from 250 to 600 rubles.

Throttle valve adjustment:

1. We loosen clamps at the connections of the intake pipe (1) and the throttle body, as well as at the junction of the large crankcase ventilation hose and the fitting (2), which is located on the cylinder head cover.

2. With the gas pedal fully depressed, the throttle should be in the fully open position. (For this action you will need the help of a partner).

3. When the gas pedal is fully released, the throttle valve should be in the fully closed position.

4. If steps 2 and 3 are not followed, the throttle cable needs adjustment.

5. If, when checking the adjustment, it is revealed that the damper does not open completely, then you should loosen the nut on the bracket, the second one from the end of the cable, and tighten the first nut until the desired effect is achieved.

6. If the throttle valve does not close completely, then do the opposite, namely, loosen the first nut from the end of the cable and tighten the second nut.

When you achieve full opening and closing of the partition when pressing and releasing the accelerator pedal, you have adjusted the throttle cable.

Video about replacing the throttle valve on an Opel Astra 1.4T:

Cleaning the throttle and throttle body on Nissan Almera:

Category: Vase repair Material:

Instructions with Photos and Videos
Video viewed:
278

Language:

Russian
Year of release:
2015
Video number:
2788965
Added by the Administration at the request of:
User.

Instructions:

Good afternoon friends. We have selected the best video for you. We wish you pleasant viewing.

What is a throttle cable

A special cable is used to open and close the throttle valve. This is where the main point of wear occurs during operation of the damper.

Self-adjustment of the throttle cable on the Lada Priora. Throttle cable lubrication

The throttle cable (gas cable) is the connecting link between the gas pedal and the throttle; when you press the pedal, you do not act on the cable, which in turn opens/closes the throttle valve.
This way you regulate the flow of fuel to the cylinders, as well as the engine speed and vehicle speed. A poor (untimely, delayed) response to pressing the gas pedal is most often a sign of problems with the throttle cable. The problem may lie in the fact that the throttle cable is incorrectly adjusted, its tension has weakened, in addition, the throttle cable may have stretched or completely failed and requires immediate replacement. If, when pressing the gas pedal, you feel resistance similar to friction, or pressing the pedal has become hard and not smooth, you need to lubricate the cable.

In this article I will talk about how to adjust the throttle cable, as well as how to lubricate the gas cable on a Lada Priora at home.

Attention! Before adjusting the throttle cable, make sure that the tight movement is not due to the carpet or other obstructions that may interfere with the free movement of the gas pedal. Very often, because of this banal “breakdown,” drivers make a lot of unnecessary movements and dismantle the engine almost to the ground in search of the reasons for the lack of engine power. As a result, it turns out that the new mat is simply bent or slipped somewhere and the pedal moves only half its travel.

Product delivery options

Note! Below are the shipping methods available specifically for this product. Payment options may vary depending on the shipping method. Detailed information can be found on the “Delivery and Payment” page.

Parcel by Russian Post

Available payment methods:

Cash on delivery (payment upon receipt)
Using cards Sberbank, VTB, Post Bank, Tinkoff
Yandex money
QIWI
ROBOKASSA

Shipping throughout Russia. Delivery time is from 5 to 12 days.

Parcel by Russian Post 1st class

Available payment methods:

Cash on delivery (payment upon receipt)
Using cards Sberbank, VTB, Post Bank, Tinkoff
Yandex money
QIWI
ROBOKASSA

Shipping throughout Russia. Delivery time is from 2 to 5 days. More expensive than regular delivery by Russian Post, approximately 50%. Parcel weight up to 2.5 kg

Express Parcel EMS

Available payment methods:

Cash on delivery (payment upon receipt)
Using cards Sberbank, VTB, Post Bank, Tinkoff
Yandex money
QIWI
ROBOKASSA

Shipping throughout Russia. Delivery time is from 3 to 7 days. More expensive than regular delivery by Russian Post, approximately 100%.

How to replace the cable on a VAZ-2110?

There are two ways to replace a torn drive, one of which is more time-consuming and requires removing additional elements from the car, but is more convenient.

With the second method, you don’t need to remove anything from the car and everything is done faster, although the ease of execution is worse. At the same time, the algorithm of work for both methods is the same, so let’s look at how everything is done using the first method, it is still more convenient and also does not take much time:

We place the car on a flat surface or the side of the road (when performing work on the road) and immobilize it with a handbrake or wheel chocks placed under the wheels. Let's see if the cable is really torn, or if the reason for the failure is a broken release bearing fork. For ease of work in the engine compartment, the battery can be removed from the car;
We release the cable in the engine compartment. If it is torn, then you can immediately pull part of it out of the winding simply by disengaging it from the lever with the clutch fork. In the case when the replacement is carried out due to “fluffing”, then first unscrew the nuts securing the cable braid (they are also adjusting) from the mounting bracket located on the gearbox housing.

We take two keys for 19 and loosen them, after which we take them out through the slot. Then we loosen the two nuts (8 and 10) of the clutch release drive and only after that we pull out the tip, for which we press the fork lever with our hands and remove the cable together with the thrust bushing.

Remove the windshield wiper bracket; to do this, unscrew two nuts. Pay attention to which direction the plane of the bracket is directed;

Since the drive is removed through the passenger compartment, from the part of the cable running in the engine part, we remove everything that can prevent it from being pulled through the technological hole - the thrust bushing, nuts 19 and washers.
Let's go to the salon. It is necessary to remove the cable end from the mounting rod on the pedal. To do this, we climb under the dashboard and find a fixing plate that keeps the tip from jumping off the rod. It is located under a protective cover.
To get to it, you will have to hold the pedal in its original position with one hand, and pry the lock with a screwdriver with the other, and this must be done carefully so as not to lose it after removal.
After this, we remove the tip from the rod. It is also advisable to remove and check the plastic bushing installed on the rod, and if signs of severe wear are noticeable, replace it during assembly;
Unscrew the nut of the cable braid fastening bracket located under the panel and remove it from the stud;
Read also: Checking current leakage in a car: step-by-step instructions
We pull the cable into the cabin, and carefully, since on many models wires pass through the technological hole for pulling the drive and it is important not to damage them or tear them away from the contacts;
We run a new cable through the hole, fasten its bracket, put the tip on the pedal rod and fix it with a plate. If the latch gets lost during the removal process, you can use a thin wire or paperclip;
We fix the cable braid on the gearbox bracket and then insert the tip with the thrust bushing into the fork lever. At this point, the replacement is completed and all that remains is to make the adjustment;
Do not forget to lubricate the clutch pedal pin and the driver with LITOL 24 grease or an equivalent.

This replacement sequence is identical for all models of the 10th series - 2110, 2111, 2112. Therefore, their cables are interchangeable.

But on earlier models - 2108-21099, the cable is different, and the sequence of work is somewhat different.

Video “Replacing the clutch cable on a VAZ car”

This video clearly shows how to replace the vehicle, as well as how to adjust the clutch pedal.

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

Replacing the choke cable on a VAZ 2109 is identical to replacing it on any other VAZ. This cable can be replaced either with the casing or completely assembled. The procedure is not complicated and any car owner can easily cope with it.

Replacing the choke cable for VAZ 2109 , 2108 starts from the engine compartment (unscrew it from the carburetor). Then we go into the car interior, pull out the choke handle and disconnect it from the cable itself. Unscrew the fastening and pull the choke cable into the passenger compartment. Then, in the same place, we install a new cable for the carburetor choke handle. Then we check the operation and, if necessary, adjust the carburetor.

How to replace the throttle cable and some drive parts on a VAZ 2108-VAZ 21099?

Replacing the throttle cable:

1) At the beginning of the operation, by hand or with a screwdriver, slide the silicone protective cap along the throttle cable.

2) Next, using two wrenches, loosen both nuts that secure the cable sheath to the bracket.

3) After the nuts are loosened, remove the cable from the slot located in the bracket.

4) Next, moving to the throttle valve itself, disconnect the tip of the cable from its sector by hand.

5) Then move to the inside of the car, and use a screwdriver to disconnect the tip of the cable from the lever pin.

6) And at the end of the operation, when the last tip is disconnected, remove the cable from the front panel, thereby removing it from the car.

Note! To install a new throttle cable, perform the entire operation in reverse order. And when the operation is completed, adjust the cable using the two tension nuts! (You can find how to adjust the cable in the article: “Adjusting the throttle”)

Replacing the gas pedal:

1) To remove the accelerator pedal, use a flathead or Phillips screwdriver to unfasten the lever return spring.

2) Next, without removing the screwdriver from your hands, use it to pick up the locking bracket.

3) And then remove it from the drive.

4) Then remove the bushing from the bent tip of the gas pedal using a lever-type screwdriver.

5) Next, slightly moving the gas pedal to the side, remove the return spring.

6) Finally, carefully remove the gas pedal from its mounting position.

Note! The new pedal is installed in the reverse order. And all deformed parts: drive bushing, locking bracket and return spring must be replaced with new ones!

VAZ 2109 | Removing, installing and adjusting the gas pedal cable

Removing, installing and adjusting the gas pedal cable

1. On E7J engines, remove the air filter assembly as described in Section Removal and Installation - Air Filter Assembly and Intake Air Ducts. On all models where it is used, unscrew the reinforcing rod between the domes of the front suspension struts.

2. At the throttle body, manually rotate the throttle valve to release the cable tension. Disconnect the cable from the sector (refer to the accompanying illustration).

3. Remove the cable casing and the O-ring from the bracket (refer to the accompanying illustration). On automatic transmission models, disconnect the overdrive switch wiring from the end of the cable housing. If necessary, remove the spring clip from the end of the cable, noting its location in the groove.

4. Working inside the vehicle, remove the lower trim panel from under the steering column. Disconnect the cable from the gas pedal by squeezing the protrusions of the cable tip (refer to the accompanying illustration).

5. Return to the engine compartment, release the cable housing from the bulkhead and remove the cable.

1. Install in reverse order; if necessary, adjust the cable as follows. Make adjustments before installing the reinforcement rod or air filter assembly.

1. After removing the spring clip from the accelerator cable housing, check that the throttle valve sector touches the limiter. Carefully pull the cable out of the O-ring, removing any play in the cable.