How to remove the dashboard on a VAZ-2107 with your own hands: step-by-step video instructions

How to remove the instrument panel on a VAZ 2107

Sometimes you still have to do it. Harnesses of wires, unimaginable poses, the feeling that you have been possessed by an octopus and one tentacle is always enough. Yes, we are talking about the instrument panel of a VAZ 2107 car. Fortunately, you have to remove it not so often, but you shouldn’t go to a service station if a light bulb has burned out or the needle on the ammeter scale has fallen off. You have to shoot it yourself.

Zaerel=0;controls=0;showinfo=0;iv_load_policy=3;" frameborder=”0″ allowfullscreen>

How to remove the instrument panel of a VAZ 2107 Mutual subscription to your channel

Hello, I'm tired of advertising on video clips on YouTube, and do you know why there are advertisements on them, for this advertising...

Replacing light bulbs on the VAZ instrument panel

In this video I will show you how to correctly change the light bulbs in the instrument

to LED! The classic is sick...

When to remove the tidy

Repairing the dashboard can be useful in the case when any of the control lamps simply burns out, and this is extremely undesirable, since the car no longer has any means of monitoring such systems as, for example, the state of the injection engine control unit (naturally, in the latest 2107 models years with an injector). The Check Engine lamp appeared only in sevens with these motors, and if it burns out or loses contact with the circuit board due to vibration or moisture, then one can only guess at the reasons for the unstable operation of the engine.

Well, the instruments themselves, the tachometer, speedometer and sensor status indicators in the systems, rarely fail, if ever.

By the way, you should pay attention to the tidy at the moment when the ignition key is turned and all the lamps flash in test mode, so to speak.

It is this moment that will make it clear that the control lamp of a particular system does not work and explanatory measures need to be carried out with it.

How to remove the tidy on the seven

The algorithm for dismantling the 2107 instrument panel is simple and here are the steps you need to perform in order, with patience:

1. The stove control knobs - the antifreeze supply lever to the heating system and the ventilation system control lever - will interfere. They should snap off using a screwdriver of a suitable diameter.
2. Resetting the odometer readings. This button is located to the right, where the emergency light button is installed. A nut is screwed onto the top of the button body. You need to unscrew it and push the button itself into the panel.
3. Now we find the thinnest slotted screwdriver and remove the plug on the right, under which the fastening screw is hidden, we unscrew it too.
4. The panel on the right is free, you can apply it to yourself, but it’s too early to rejoice. All that remains is to remove the speedometer cable, the econometer vacuum tube and unclip the wiring harnesses.
5. Now, with an effort of will and sleight of hand, you need to unscrew the cable nut. It's not hard to do, it's hard to get there. It might be faster if you try on the right.
6. The econometer hose is also easy to remove. But you need to be able to get to it. Let's take it off too.
7. We disconnect the pads from the harnesses by touch and remember where each one was, although you need to have a special talent to mix them up.

Actually, that's all. Now you can take out the device and do whatever you want and need with it. Since we have the tidy in our hands, maybe it makes sense to think about installing LEDs instead of incandescent lamps? In any case, good work and smooth roads!

Source: https://5net.ru/kak-snjat-shhitok-priborov-na-vaz-2107/

Seven dashboard design

In terms of science intensity and level of professionalism, there can be no special complaints about the person performing this operation. If the owner knows how to disassemble an electric kettle and what is the best way to do it, then how to remove the instrument panel on a VAZ 2107 will certainly not raise any questions. Difficulties will appear only the first time, when before this you have not had to disassemble the Zhiguli front panel and pick out the tidy from it.

Absolutely all modifications 2107 and 2105 have a similar algorithm for dismantling the tidy, which we will announce today to help desperate owners who decide to spend a day off replacing a light bulb. First you need to be patient, this is the most important thing, and then have a good set of screwdrivers of different lengths and thicknesses. We will use them as assembly blades and manipulators where it is physically impossible to reach with our hands.

Tuning the instrument panel of a VAZ 2107, how to remove and disassemble the panel

The dashboard is an integral and important part of any car. Not only driving comfort but also safety directly depends on the ease of reading information. During the production of the model, the appearance of the dashboard on this model changed slightly.

The latest version of the execution contained the following information:

• Tachometer - shows the number of crankshaft revolutions per minute. This feature appeared on the dashboard in the late 80s;
• Speedometer – accordingly shows the current speed;
• An econometer is a rare option even for modern cars. This sensor shows what speed is best to drive at the current moment to effectively save fuel;
• Oil pressure sensor (warning light). The sensor shows the engine oil level, and the warning light starts blinking if a malfunction occurs;
• Fuel level – the arrow indicates the amount of gasoline in the tank;
• Battery charge sensor – shows the device charge level;

Dashboard diagram

VAZ 2107 instrument panel diagram

In order to have complete information about the condition of the car, you need to understand the instrument panel diagram, however, for cars with an injector it differs.

Below is a description of the elements of the instrument panel:

1 - charging the battery; 2 — speedometer; 3 - odometer - car mileage counter; 4 – tachometer; 5 — coolant temperature sensor; 6 — ECON – indicator of economical fuel consumption; 7 - instrument cluster, including control lights: right and left turn on, malfunction in the power unit system, battery charging light, side lights on, high beam on, oil pressure sensor, handbrake on; 8 — daily mileage of the car; 9 — fuel reserve lamp; 10 — fuel level indicator in the gas tank.

Tidy keys VAZ 2107

1. Key to turn off external lighting.
2. Rear window heating switch.
3. The key to turn on the fog light when the low beam headlights are on.
4. Heater fan speed switch.

How to Remove the Dashboard of a VAZ 2107 Video ~ AUTOTEXNIKA.RU

Home page » How to Remove the Dashboard of a VAZ 2107 Video

14.09.2018

We independently remove the dashboard of a VAZ 2107

For a novice car enthusiast, removing the toolbar may not seem too difficult. But this impression is deceptive. Before the dashboard

The VAZ 2107 will be completely removed; we will have to do a lot of manipulations, which we will tell the reader about in this article.

The most common reasons for dismantling

• One or more devices failed.
• The panel joints began to creak during the trip, and the car owner decided to glue them from the inside to eliminate this annoying creak.
• Several light bulbs burned out on the panel.
• The speedometer cable has become unusable and requires urgent replacement.

Required Tools

1. Set of car keys.
2. Flat blade screwdriver (medium size).
3. Cross screwdriver (medium size).
4. Pliers.

How to remove the instrument panel and shield VAZ 2107

1. The car hood opens and the negative terminal is removed from the battery.
2. Using a screwdriver, the dashboard
   and glove box housing are unscrewed and removed.
3. The two connectors that supply the glove lights in the glove box are now disconnected.
   Light bulb power connectors are disconnected
4. The sub-instrument panel is carefully clamped with a flathead screwdriver on the lower right edge and its clips are removed from the grooves, after which they are removed along with all devices.
   Additional panel

   can be removed with a screwdriver

5. Behind this panel there are connectors from which the lighting of devices, clocks, warning lights and the cigarette lighter are activated. All this is disabled. Additional connectors are disabled manually
6. Use a flathead screwdriver to push out all the switches located near the gear shift lever.
   Switch connectors are disabled.
7. There are two screws under the switches. They are unscrewed with a screwdriver. The screws are tightened with a Phillips screwdriver
8. Using a 10 wrench, the top bolts holding the center console are unscrewed.
   After this it is deleted. The center console is removed manually
9. A Phillips-head screwdriver is unscrewed using the self-tapping screws that hold the lower protective cover of the steering column, after which it is removed along with the upper half of the column housing.
10. The tips on the stove sticks are pierced with a screwdriver and then removed by hand.
    The deflector channels are located next to them; they are also removed manually. After this, the 4 screws that hold the cover on the heating system are removed and it is removed.
11. A Phillips head screwdriver is used to remove the screws holding the furnace control unit to the dashboard.
    This opens up access to the screws that hold the screen with the devices. The right edge of the flap is pulled out so that an arm that passes through the gap is formed. After this, the fastening nut of the speedometer cable is unscrewed behind the valve, all other wires are disconnected. The instrument panel has been removed. The shield is removed from its original position
12. Provides access to the upper mounting nuts of the instrument panel. They are unscrewed with a 10 mm carabiner wrench. The panel is then removed. The instrument panel has been completely removed
13. Reassemble in reverse order.

How to remove the instrument panel of a VAZ 2107

Removing the instrument panel of a VAZ 2107

.

Replacing light bulbs on the VAZ instrument panel

In this video

I will show you how to correctly change the light bulbs in
the instrument panel
to LED ones! The classic is sick.

Video of removing the instrument panel on seven

Important points

• It is recommended to label wires and connectors before disconnecting them to make assembly easier. These marks are easy to apply with a black marker or felt-tip pen (since most of the connectors are located under the white dashboard).
• To remove
  the upper part of the steering column protective cover, it is necessary to be precise, since you can damage the rubber ring on the ignition switch (it gets caught on the edge of the housing and breaks easily).
• When removing the optional panel, do not tilt the screwdriver too far; the latches that hold this panel in place are plastic and break very easily.

As can be seen from this article, removing the dashboard for the VAZ 2107 task is both labor-intensive, but feasible. Main.

Follow the instructions above and do not use too much force when removing: the panel material, despite its apparent strength, breaks quite easily.

Source: https://autotexnika.ru/kak-snjat-panel-priborov-vaz-2107-video/

Difference algorithm on a car with air conditioning

We read the indicators and repair the dashboard on the Volga
"Kalina" with air conditioning has two heater radiators and differs from models without a climate control temperature regulator in the cabin. There are two radiators, because through one of them there is a freon air conditioner, and in another way. antifreeze, like in a car without air conditioning. Accordingly, the temperature controller allows air to pass through one of the radiators depending on its position. It will be more difficult to dismantle such a structure and replace the necessary elements on your own.

To understand that the oven has become unusable, it does not work immediately, because the leaking liquid quickly evaporates and only reminds of a specific smell

When replacing a radiator, you must carefully place the parts that need to be removed, do not deviate from the instructions and follow safety precautions

How to remove the instrument panel on a VAZ 2107 (photo and video)

Removing the instrument panel (or dashboard) is required for many purposes: changing light bulbs, the panel itself, and control devices. You need to remove the panel in order to tune it, and some unscrupulous “specialists” get to the meter this way and “twist” the mileage. Regardless of whether it is a carburetor VAZ 2107 or an injector, the removal diagram is the same.

Below is the instrument cluster for the VAZ 2107 injector:

The difference in the combination is insignificant: if you have an injector, then an engine management system malfunction indicator is added:

The symbol lights up when ignited, and goes out after a stable start. Constantly lights up or flashes if the injector is faulty or the engine is not working properly.

Let's look at the sequence of actions to remove the panel.

1. Remember: almost all work on servicing electrical circuits in a VAZ 2107 car, and in any other car, begins with “de-energizing the mass,” or opening the negative part of the circuit, which serves as the body. To do this, you need to remove the negative terminal from the battery.
2. Using a straight-blade screwdriver, carefully remove the three caps from the interior heater control levers. Any scheme for the removal order.
3. To the right of the levers you can see a plug with a heating symbol. Use the same screwdriver to pry it off. Removing the plug is easy. Under it there is a screw - a self-tapping screw that secures the right side of the dashboard. We unscrew it.
4. To the right of the alarm button there is a recessed handle that “resets” the daily mileage. You need to unscrew and pull out the nut along with the washer, and push the handle itself inside the panel.
5. Carefully pull the right side of the panel towards you, next to the heater levers.
6. Now you need to disconnect the speedometer drive cable. We put on cotton gloves so as not to stain our hands with oil, and unscrew the nut on the cable. It has a grooved rim and is shown with an arrow.
7. Remove the vacuum supply hose from the economizer fitting. For VAZ 2107 it is located on the left side of the dashboard. Sometimes it resists, so you can gently apply force.
8. Important point! Before disconnecting different colored pads, remember the markings and joint locations, or write down where they are connected. Only after this can the connectors be opened. If the connection diagram is broken during assembly, you will have to disassemble everything again.
9. The final stage: we remove the shield. The operation is completed.

When installing the shield, all steps are performed in reverse order. Before installing the panel, do not forget to connect all contacts, place the negative terminal on the battery and turn on the ignition. Because if you forget to connect something, you will need to completely remove the panel again.

Once you have removed the panel, you can do its tuning. For example, change the appearance of the dials. To do this, first carefully remove the arrows, while trying not to bend them or the pins. The movement is only “pulling” perpendicular to the plane of the dial (do not forget to mark the place where the hand “lies” in the zero position before removing it).

The next step is to glue on the new dial; for good quality of the sticker, the surface needs to be degreased and the sticker carefully rolled.

You can also tune the dashboard lighting by setting the LEDs to 12 V, current 350 mA. The main thing when soldering is not to forget to put a resistor in the series circuit to protect against overload.

LEDs can be installed instead of standard lamps, and a rheostat can be included in the circuit.

The photo shows a decent tuning of the VAZ 2107 dashboard in day and night lighting options.

Source: https://7vaz.ru/remont/panel-priborov.html

Additional Helpful Tips

The owner of a VAZ car has the opportunity to make a beard himself from scratch. But before starting work, it is highly recommended to study the drawings on the Internet. A large number of other drivers of VAZ 2107, 2106 and 2105 have published their options for creating a beard with an individual appearance and corresponding drawings.

Be responsible in determining the optimal sizes

In addition to the dimensions of the radio, the amount of usable space in the cabin is also taken into account. The console should not create any discomfort for the legs of the driver and passenger

Under no circumstances should you proceed straight to cutting out the plywood. A do-it-yourself cardboard blank will allow you to accurately assess the degree of comfort. A custom console for a VAZ is created to simplify access to the radio, taking into account the location of the gear lever. But here you can also make convenient compartments for storing small personal items. Again, a pre-created blank made of hard cardboard will help with this.

conclusions

The beard of VAZ cars makes it possible to significantly simplify driving comfort. Both the driver and the passenger will not have to reach for the radio. Depending on the design, you can also place additional cells here to store parts or small personal items. It usually takes several days to create a part. You need to be prepared for this right away. Under no circumstances should you start by cutting plywood, as there is a high chance that you will not be able to install it. A cardboard blank will allow you to modernize the design taking into account individual needs. Of course, in addition to creating a beard with your own hands, you can also seek help from a specialized car service. But why, if this method will save a lot of money? Therefore, feel free to take on interior tuning, starting with the console!

On the front panel of the VAZ 2107 in the middle there is a console (beard), on which various equipment is placed (clock, radio, switches, indicators). This part of the car interior is often called “beard” by drivers.

Often car enthusiasts pay special attention to this console, making it original and at the same time increasing its functionality. Beard tuning includes adding additional devices and elements that make it more informative and useful:

• Car radio.
• Dashboard lighting control.
• USB sockets for charging smartphones and tablets.
• Watch.
• Switch for fog lights, exterior lighting, heated rear window.
• Vehicle control instruments (ammeter, voltmeter).
• Pocket for small items near the gearshift lever.

Possible reasons for dismantling the shield

In what cases is it necessary to remove the dashboard of a VAZ 2107 car? There may be several reasons for this:

• panel tuning;
• replacing burnt out light bulbs;
• repair of individual devices that have failed.

VAZ 2107 is a legendary car, which hundreds of thousands of car enthusiasts have repaired independently.

Possible reasons for dismantling the shield

In what cases is it necessary to remove the dashboard of a VAZ 2107 car? There may be several reasons for this:

• panel tuning;
• replacing burnt out light bulbs;
• repair of individual devices that have failed.

VAZ 2107 is a legendary car, which hundreds of thousands of car enthusiasts have repaired independently.

Replacing light bulbs

To change the lights on the tidy, you first need to remove it.
How to do this is indicated above. After dismantling it will need to be disassembled. This is done by snapping out the terminals. The result should look like this.

The photo above shows the location of the light bulbs mounted in the car's dashboard.

After disassembly, you need to unscrew the illuminator along with the socket and install a new element in its place.

There are only two types of light bulbs used on the car panel.

• Direct lighting – AMN 12-3-1. Modern standard T3W.
• Indicators A12-1.2 or, in a new way, W1.2.